Remove ads
.jpg)
 | This article needs to be updated. (April 2022) |
The Z Pulsed Power Facility, informally known as the Z machine or simply Z,[1] is the largest high frequency electromagnetic wave generator in the world, operated by Sandia National Laboratories in Albuquerque, New Mexico.
It has primarily been used as an inertial confinement fusion (ICF) research facility, including the magnetized liner inertial fusion (MagLIF) approach, and for testing materials in conditions of extreme temperature and pressure. In particular, it gathers data to aid in computer modeling of nuclear weapons and eventual fusion pulsed power plants.
Remove ads
The Z machine's origins can be traced to the Department of Energy (DoE) needing to replicate the fusion reactions of a thermonuclear bomb in a lab environment to better understand the physics involved. Since the 1970s, the DoE has also been looking into ways to generate electricity from fusion reactions.
The first research at Sandia, headed by Gerold Yonas[2][3] – the particle-beam fusion program – dates back to 1971.[4] This program tried to generate fusion by compressing fuel with beams of charged particles. Electrons were the first particles to be thought of, because the pulsed power accelerators at the time had already concentrated them at high power in small areas. However, shortly thereafter it was realized that electrons can not possibly heat the fusion fuel rapidly enough for the purpose. The program then moved away from electrons in favor of protons. These turned out to be too light to control well enough to concentrate onto a target, and the program moved on to light ions, lithium. The accelerators names reflect the change in emphasis: first the accelerator's name was EBFA-I (electron beam fusion accelerator), shortly thereafter PBFA-I, which became Saturn. Protons demanded another accelerator, PBFA-II, which became Z.
The November 1978 issue of Scientific American carried Yonas' first general-public article, "Fusion power with particle beams".[5]
In 1985, the PBFA-II was created.[6][7] Sandia continued to target heavy ion fusion at a slow pace despite the National Academies report.
Meanwhile, defense-related research was also ongoing at Sandia with the Hermes III machine and Saturn (1987), upgraded from PBFA-I, which operated at lower total power than PBFA-II but advanced Sandia's knowledge in high voltage and high current and was therefore a useful predecessor to the Z machine.
Also in 1996, the PBFA-II machine was once again upgraded[8] into PBFA-Z[9] or simply "Z machine", described for the first time to the general public in August 1998 in Scientific American.[10]
Remove ads
- A laser preheats the fuel.
- An axial current is driven through the liner.
- The current induces an azimuthal magnetic field.
- The magnetic force implodes the liner, compressing and further heating the fuel.
The Z machine uses the well known principle of Z-pinch to produce hot short-lived plasmas. The plasma can be used as a source of x-rays, as a surrogate for the inside of a thermonuclear weapon, or as a surrogate for the core of a fusion power plant.
In a Z-pinch, the fast discharge of current through a column of plasma causes it to be compressed towards its axis by the resulting Lorentz forces, thus heating it. Willard Harrison Bennett successfully researched the application of Z-pinches to plasma compression. The Z machine layout is cylindrical. On the outside it houses huge capacitors discharging through Marx generators which generate a one microsecond high-voltage pulse. This pulse is then compressed by a factor of 10 to enable the creation of 100 ns discharges.
Most experiments on the Z machine run the current discharge through a conductive tube (called a liner) filled with gas. This approach is known as magnetized liner inertial fusion, or MagLIF. The compression of a MagLIF Z-pinch is limited because the current flow is highly unstable and rotates along the cylinder which causes twisting of the imploding tube therefore decreasing the quality of the compression.
The Z machine has also conducted experiments with arrays of tungsten wires rather than liners. The space inside the wire array was filled with polystyrene, which helps homogenize the X-ray flux. By removing the polystyrene core, Sandia was able to obtain a thin 1.5 mm plasma cord in which 10 million amperes flowed with 90 megabars of pressure.[citation needed]
Remove ads
The key attributes of Sandia's Z machine[11] are its 18 million amperes of current and a discharge time of less than 100 nanoseconds. This current discharge was initially run through an array of tungsten wires.[12] In 1999, Sandia tested the idea of nested wire arrays;[13] the second array, out of phase with the first, compensates for Rayleigh-Taylor instabilities. In 2001, Sandia introduced the Z-Beamlet laser (from surplus equipment of the National Ignition Facility) as a tool to better image the compressing pellet.[14] This confirmed the shaping uniformity of pellets compressed by the Z machine.
In 1999, Sandia started the Z-IFE project,[15] which aimed to solve the practical difficulties in harnessing fusion power. Major problems included producing energy in a single Z-pinch shot, and quickly reloading the reactor after each shot. By their early estimates, an implosion of a fuel capsule every 10 seconds could economically produce 300 MW of fusion energy.
Sandia announced the fusing of small amounts of deuterium in the Z machine on April 7, 2003.[16]
Besides being used as an X-ray generator, the Z machine propelled small plates at 34 kilometers a second, faster than the 30 kilometers per second that Earth travels in its orbit around the Sun, and four times Earth's escape velocity (3 times it at sea level).[17] It also successfully created a special, hyperdense "hot ice" known as ice VII, by quickly compressing water to pressures of 70,000 to 120,000 atmospheres (7 to 12 GPa).[18] Mechanical shock from impacting Z-machine accelerated projectiles is able to melt diamonds.[19]
During this period the power of X-ray produced jumped from 10 to 300TW.[20] In order to target the next milestone of fusion breakeven, another upgrade was then necessary[21]
Remove ads
104 m diameter, 70 megaamperes, 24 megavolts.
A $60 million (raised to $90 million) retrofit program called ZR (Z Refurbished) was announced in 2004 to increase its power by 50%. The Z machine was dismantled in July 2006 for this upgrade, including the installation of newly designed hardware and components and more powerful Marx generators. The deionized water section of the machine has been reduced to about half the previous size while the oil section has been expanded significantly in order to house larger intermediate storage lines (i-stores) and new laser towers, which used to sit in the water section. The refurbishment was completed in October 2007.[22] The newer Z machine can now shoot around 26 million amperes[23] (instead of 18 million amperes previously) in 95 nanoseconds. The radiated power has been raised to 350 terawatts and the X-ray energy output to 2.7 megajoules. In 2006 wire array experiments reach ultra-high temperatures (2.66 to 3.7 billion kelvins).[24]
Sandia's roadmap for the future includes another Z machine version called ZN (Z Neutron) to test higher yields in fusion power and automation systems. ZN is planned to give between 20 and 30 MJ of hydrogen fusion power with a shot per hour using a Russian Linear Transformer Driver (LTD) replacing the current Marx generators.[25] After 8 to 10 years of operation, ZN would become a transmutation pilot plant capable of a fusion shot every 100 seconds.[26]
The next step planned would be the Z-IFE (Z-inertial fusion energy) test facility, the first true z-pinch driven prototype fusion power plant. It is suggested it would integrate Sandia's latest designs using LTDs. Sandia Labs recently proposed a conceptual 1 petawatt (1015 watts) LTD Z-pinch power plant, where the electric discharge would reach 70 million amperes.[27] As of 2012, fusion shot simulations at 60 to 70 million amperes are showing a 100 to 1000 fold return on input energy. Tests at the Z machine's current design maximum of 26-27 million amperes were set to begin in 2013.[28][29][clarification needed]
Remove ads
Remove ads
Wikiwand in your browser!
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.
Remove ads