Scancode
Data sent by computer keyboard keypress From Wikipedia, the free encyclopedia
A scancode (or scan code) is the data that most computer keyboards send to a computer to report which keys have been pressed. A number, or sequence of numbers, is assigned to each key on the keyboard.
 | This article needs additional citations for verification. (October 2011) |
Mapping key positions by row and column requires less complex computer hardware; therefore, in the past, using software or firmware to translate the scancodes to text characters was less expensive than wiring the keyboard by text character.[1] This cost difference is not as profound as it used to be. However, many types of computers still use their traditional scancodes to maintain backward compatibility.
Some keyboard standards include a scancode for each key being pressed and a different one for each key being released. In addition, many keyboard standards (for example, IBM PC compatible standards) allow the keyboard itself to generate "typematic" repeating keys by having the keyboard itself generate the pressed-key scancode repeatedly while the key is held down, with the release scancode sent once when the key is released.
On some operating systems one may discover a key's downpress scancode by holding the key down while the computer is booting. With luck, the scancode (or some part of it) will be specified in the resulting "stuck key" error message. [Note: On Windows 7 only one byte of the scancode appears.]
PC compatibles
Scancodes on IBM PC compatible computer keyboards are sets of 1 to 3 bytes which are sent by the keyboard. Most character keys have a single byte scancode; keys that perform special functions have 2-byte or 3-byte scancodes, usually beginning with the byte (in hexadecimal) E0, E1, or E2. In addition, a few keys send longer scancodes, effectively emulating a series of keys to make it easier for different types of software to process.
PC keyboards since the PS/2 keyboard support up to three scancode sets. The most commonly encountered are the "XT" ("set 1") scancodes, based on the 83-key keyboard used by the IBM PC XT and earlier. These mostly consist of a single byte; the low 7 bits identify the key, and the most significant bit is clear for a key press or set for a key release. Some additional keys have an E0 (or rarely, E1 or E2) prefix. These were initially assigned so that ignoring the E0 prefix (which is in the key-up range and thus would have no effect on an operating system that did not understand them) would produce reasonable results. For example the numeric keypad's Enter key produces a scancode of E0 1C, which corresponds to the Return key's scancode of 1C.
The IBM 3270 PC introduced its own set of scancodes ("set 3"), with a different key numbering and where a key release is indicated by an F0 prefix. For backward compatibility, the 3270 PC translated these to XT (set 1) scancodes using an add-on card and a BIOS extension. This set is used by Linux by default when it detects a PS/2 keyboard that can properly support scan code set 3.[2]
The IBM PC AT introduced the "AT" ("set 2") scancodes. On the 84-key AT keyboard these were largely a subset of set 3, with some differences caused by the revised layout (for example, the position and scancodes of the function keys changed). Keys added since the PC AT often have different scancodes in set 2 and set 3, and in set 2 frequently have an E0 or E1 prefix. Again, key release is indicated by an F0 prefix.
For computers since the IBM PC AT, the keyboard controller on the motherboard translates AT (set 2) scancodes into XT (set 1) scancodes in so called translation mode.[3] This translation can be disabled in pass-through-mode, allowing the raw scancodes to be seen.[4] Therefore, whether a software developer will encounter AT scancodes or XT scancodes on a modern PC-compatible depends on how the keyboard is being accessed.
A compliant PS/2 keyboard can be told to send scancodes in set 1, 2 or 3.
| key | set 1 (IBM PC XT) | set 2 (IBM PC AT) | set 3 (IBM 3270 PC) | |||
|---|---|---|---|---|---|---|
| press | release | press | release | press | release | |
| A (simple letter) | 1E |
9E |
1C |
F0 1C |
1C |
F0 1C |
| ↵ Enter (main keyboard) | 1C |
9C |
5A |
F0 5A |
5A |
F0 5A |
| ↵ Enter (numeric keypad) | E0 1C |
E0 9C |
E0 5A |
E0 F0 5A |
79 |
F0 79 |
| Left ⊞ Win (Windows key) | E0 5B |
E0 DB |
E0 1F |
E0 F0 1F |
8B |
F0 8B |
| Right ⊞ Win | E0 5C |
E0 DC |
E0 27 |
E0 F0 27 |
8C |
F0 8C |
USB
USB keyboards use a new set of scancodes, mostly specified in the USB standard. All computers that recognize USB keyboards recognize these new scancodes.[5]
Wikiwand in your browser!
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.
