Loading AI tools
Device for weaving textiles From Wikipedia, the free encyclopedia
A loom is a device used to weave cloth and tapestry. The basic purpose of any loom is to hold the warp threads under tension to facilitate the interweaving of the weft threads. The precise shape of the loom and its mechanics may vary, but the basic function is the same.
The word "loom" derives from the Old English geloma, formed from ge- (perfective prefix) and loma, a root of unknown origin; the whole word geloma meant a utensil, tool, or machine of any kind. In 1404 "lome" was used to mean a machine to enable weaving thread into cloth.[1][2][failed verification] By 1838 "loom" had gained the additional meaning of a machine for interlacing thread.[citation needed]
Weaving is done on two sets of threads or yarns, which cross one another. The warp threads are the ones stretched on the loom (from the Proto-Indo-European *werp, "to bend"[3]). Each thread of the weft (i.e. "that which is woven") is inserted so that it passes over and under the warp threads.
The ends of the warp threads are usually fastened to beams. One end is fastened to one beam, the other end to a second beam, so that the warp threads all lie parallel and are all the same length. The beams are held apart to keep the warp threads taut.
The textile is woven starting at one end of the warp threads, and progressing towards the other end. The beam on the finished-fabric end is called the cloth beam. The other beam is called the warp beam.
Beams may be used as rollers to allow the weaver to weave a piece of cloth longer than the loom. As the cloth is woven, the warp threads are gradually unrolled from the warp beam, and the woven portion of the cloth is rolled up onto the cloth beam (which is also called the takeup roll). The portion of the fabric that has already been formed but not yet rolled up on the takeup roll is called the fell.
Not all looms have two beams. For instance, warp-weighted looms have only one beam; the warp yarns hang from this beam. The bottom ends of the warp yarns are tied to dangling loom weights.
A loom has to perform three principal motions: shedding, picking, and battening.
There are also usually two secondary motions, because the newly constructed fabric must be wound onto cloth beam. This process is called taking up. At the same time, the warp yarns must be let off or released from the warp beam, unwinding from it. To become fully automatic, a loom needs a tertiary motion, the filling stop motion. This will brake the loom if the weft thread breaks.[4] An automatic loom requires 0.125 hp to 0.5 hp to operate.
A loom, then, usually needs two beams, and some way to hold them apart. It generally has additional components to make shedding, picking, and battening faster and easier. There are also often components to help take up the fell.
The nature of the loom frame and the shedding, picking, and battening devices vary. Looms come in a wide variety of types, many of them specialized for specific types of weaving. They are also specialized for the lifestyle of the weaver. For instance, nomadic weavers tend to use lighter, more portable looms, while weavers living in cramped city dwellings are more likely to use a tall upright loom, or a loom that folds into a narrow space when not in use.
Loom frames can be roughly divided, by the orientation of the warp threads, into horizontal looms and vertical looms. There are many finer divisions. Most handlooom frame designs can be constructed fairly simply.[5]
The back-strap loom (also known as belt loom)[6] is a simple loom with ancient roots, still used in many cultures around the world (such as Andean textiles). It consists of two sticks or bars between which the warps are stretched. One bar is attached to a fixed object and the other to the weaver, usually by means of a strap around the weaver's back. The weaver leans back and uses their body weight to tension the loom.
Both simple and complex textiles can be woven on backstrap looms. They produce narrowcloth: width is limited to the weaver's armspan. They can readily produce warp-faced textiles, often decorated with intricate pick-up patterns woven in complementary and supplementary warp techniques, and brocading. Balanced weaves are also possible on the backstrap loom.
The warp-weighted loom is a vertical loom that may have originated in the Neolithic period. Its defining characteristic is hanging weights (loom weights) which keep bundles of the warp threads taut. Frequently, extra warp thread is wound around the weights. When a weaver has woven far enough down, the completed section (fell) can be rolled around the top beam, and additional lengths of warp threads can be unwound from the weights to continue. This frees the weaver from vertical size constraint. Horizontally, breadth is limited by armspan; making broadwoven cloth requires two weavers, standing side by side at the loom.
Simple weaves, and complex weaves that need more than two different sheds, can both be woven on a warp-weighted loom. They can also be used to produce tapestries.
In pegged looms, the beams can be simply held apart by hooking them behind pegs driven into the ground, with wedges or lashings used to adjust the tension. Pegged looms may, however, also have horizontal sidepieces holding the beams apart.
Such looms are easy to set up and dismantle, and are easy to transport, so they are popular with nomadic weavers. They are generally only used for comparatively small woven articles.[9] Urbanites are unlikely to use horizontal floor looms as they take up a lot of floor space, and full-time professional weavers are unlikely to use them as they are unergonomic. Their cheapness and portability is less valuable to urban professional weavers.[10]
In a treadle loom, the shedding is controlled by the feet, which tread on the treadles.
The earliest evidence of a horizontal loom is found on a pottery dish in ancient Egypt, dated to 4400 BC. It was a frame loom, equipped with treadles to lift the warp threads, leaving the weaver's hands free to pass and beat the weft thread.[11]
A pit loom has a pit for the treadles, reducing the stress transmitted through the much shorter frame.[12]
In a wooden vertical-shaft loom, the heddles are fixed in place in the shaft. The warp threads pass alternately through a heddle, and through a space between the heddles (the shed), so that raising the shaft raises half the threads (those passing through the heddles), and lowering the shaft lowers the same threads — the threads passing through the spaces between the heddles remain in place.
A treadle loom for figured weaving may have a large number of harnesses or a control head. It can, for instance, have a Jacquard machine attached to it[13] .
Tapestry can have extremely complex wefts, as different strands of wefts of different colours are used to form the pattern. Speed is lower, and shedding and picking devices may be simpler. Looms used for weaving traditional tapestry are called not as "vertical-warp" and "horizontal-warp", but as "high-warp" or "low-warp" (the French terms haute-lisse and basse-lisse are also used in English).[14]
Inkle looms are narrow looms used for narrow work. They are used to make narrow warp-faced strips such as ribbons, bands, or tape. They are often quite small; some are used on a tabletop. others are backstraps looms with a rigid heddle, and very portable.
There exist very small hand-held looms known as darning looms. They are made to fit under the fabric being mended, and are often held in place by an elastic band on one side of the cloth and a groove around the loom's darning-egg portion on the other. They may have heddles made of flip-flopping rotating hooks [15] Other devices sold as darning looms are just a darning egg and a separate comb-like piece with teeth to hook the warp over; these are used for repairing knitted garments and are like a linear knitting spool.[16] Darning looms were sold during World War Two clothing rationing in the United Kingdom[17] and Canada,[18] and some are homemade.[19][20]
.Circular looms are used to create seamless tubes of fabric for products such as hosiery, sacks, clothing, fabric hoses (such as fire hoses) and the like. Tablet weaving can be used to knit tubes, including tubes that split and join.
Small jigs also used for circular knitting are also sometimes called circular looms,[21] but they are used for knitting, not weaving.
It is possible to weave by manually threading the weft over and under the warp threads, but this is slow. Some tapestry techniques use manual shedding. Pin looms and peg looms also generally have no shedding devices. Pile carpets generally do not use shedding for the pile, because each pile thread is individually knotted onto the warps, but there may be shedding for the weft holding the carpet together.
Usually weaving uses shedding devices. These devices pull some of the warp threads to each side, so that a shed is formed between them, and the weft is passed through the shed. There are a variety of methods for forming the shed. At least two sheds must be formed, the shed and the countershed. Two sheds is enough for tabby weave; more complex weaves, such as twill weaves, satin weaves, diaper weaves, and figured (picture-forming) weaves, require more sheds.
A shed-rod (shedding stick, shed roll) is simply a stick woven through the warp threads. When pulled perpendicular to the threads (or rotated to stand on edge, for wide, flat shedding rods), it creates a shed. To create the counter-shed, a heddle-bar is usually used.
Elements of a warp-weighted loom |
![]() |
See body text for labels. |
A heddle-bar is simply a stick placed across the warp and tied to individual warp threads. When it is lifted, it pulls the warp threads it is tied to out of position, creating a shed.
A warp-weighted loom (see diagram) typically uses a heddle-bar. It has two upright posts (C); they support a horizontal beam (D), which is cylindrical so that the finished cloth can be rolled around it, allowing the loom to be used to weave a piece of cloth taller than the loom, and preserving an ergonomic working height. The warp threads (F, and A and B) hang from the beam and rest against the shed rod (E). The heddle-bar (G) is tied to some of the warp threads (A, but not B), using loops of string called leashes (H). So when the heddle rod is pulled out and placed in the forked sticks protruding from the posts (not lettered, no technical term given in citation), the shed (1) is replaced by the counter-shed (2). By passing the weft through the shed and the counter-shed, alternately, cloth is woven.[22]
Heddle-rods are used on modern tapestry looms.
Tablet weaving uses cards punched with holes. The warp threads pass through the holes, and the cards are twisted and shifted to created varied sheds. This shedding technique is used for narrow work. It is also used to finish edges, weaving decorative selvage bands instead of hemming.
There are heddles made of flip-flopping rotating hooks, which raise and lower the warp, creating sheds. The hooks, when vertical, have the weft threads looped around them horizontally. If the hooks are flopped over on side or another, the loop of weft twists, raising one or the other side of the loop, which creates the shed and countershed.[23]
Rigid heddles are generally used on single-shaft looms. Odd warp threads go through the slots, and even ones through the circular holes, or vice-versa. The shed is formed by lifting the heddle, and the countershed by depressing it. The warp threads in the slots stay where they are, and the ones in the circular holes are pulled back and forth. A single rigid heddle can hold all the warp threads, though sometimes multiple rigid heddles are used.
Treadles may be used to drive the rigid heddle up and down.
Rigid heddles (above) are called "rigid" to distinguish them from string and metal heddles, where each warp thread has its own heddle, which has an eye at each end and one in the middle for the warp thread. The eyes in the ends are fastened to a shaft, all in a row. This requires multiple shafts; it cannot be done on a single-shaft loom. The different shafts (also called harnesses) must be controlled by some mechanism.
While non-rigid heddles generally mean that two shafts are needed even for a plain tabby weave, twill weaves require three or more (depending on the type of twill), and more complex figured weaves require still more harnesses.
Treadle looms can control multiple harnessess with multiple treadles. The weaver selects which harnesses are engaged with their feet. One treadle may be connected to more than one harness, and any number of treadles can be engaged at once, meaning that the number of different sheds that can be selected is two to the power of the number of treadles. Eight is a large but reasonable number of treadles, giving a maximum of 28=256 sheds (some of which will not have enough threads on one side to be useful). The weaver must remember the sequence of treadling needed to produce the pattern.
A drawloom is for weaving figured cloth. In a drawloom, a "figure harness" is used to control each warp thread separately,[24] allowing very complex patterns. A drawloom requires two operators, the weaver, and an assistant called a "drawboy" to manage the figure harness.
The earliest confirmed drawloom fabrics come from the State of Chu and date c. 400 BC.[25] Some scholars speculate an independent invention in ancient Syria, since drawloom fabrics found in Dura-Europas are thought to date before 256 AD.[25][26] The draw loom was invented in China during the Han dynasty (State of Liu?);[contradictory][27] foot-powered multi-harness looms and jacquard looms were used for silk weaving and embroidery, both of which were cottage industries with imperial workshops.[28] The drawloom enhanced and sped up the production of silk and played a significant role in Chinese silk weaving. The loom was introduced to Persia, India, and Europe.[27]
A dobby head is a device that replaces the drawboy, the weaver's helper who used to control the warp threads by pulling on draw threads. "Dobby" is a corruption of "draw boy". Mechanical dobbies pull on the draw threads using pegs in bars to lift a set of levers. The placement of the pegs determines which levers are lifted. The sequence of bars (they are strung together) effectively remembers the sequence for the weaver. Computer-controlled dobbies use solenoids instead of pegs.
The Jacquard loom is a mechanical loom, invented by Joseph Marie Jacquard in 1801, which simplifies the process of manufacturing figured textiles with complex patterns such as brocade, damask and matelasse.[29][30] The loom is controlled by punched cards with punched holes, each row of which corresponds to one row of the design. Multiple rows of holes are punched on each card and the many cards that compose the design of the textile are strung together in order. It is based on earlier inventions by the Frenchmen Basile Bouchon (1725), Jean Baptiste Falcon (1728) and Jacques Vaucanson (1740).[31] To call it a loom is a misnomer, a Jacquard head could be attached to a power loom or a handloom, the head controlling which warp thread was raised during shedding. Multiple shuttles could be used to control the colour of the weft during picking. The Jacquard loom is the predecessor to the computer punched card readers of the 19th and 20th centuries.[32]
The weft may be passed across the shed as a ball of yarn, but usually this is too bulky and unergonomic. Shuttles are designed to be slim, so they pass through the shed; to carry a lot of yarn, so the weaver does not need to refill them too often; and to be an ergonomic size and shape for the particular weaver, loom, and yarn. They may also be designed for low friction.
At their simplest, these are just sticks wrapped with yarn. They may be specially shaped, as with the bobbins and bones used in tapestry-making (bobbins are used on vertical warps, and bones on horizontal ones).[33][34]
Boat shuttles may be closed (central hollow with a solid bottom) or open (central hole goes right through). The yarn may be side-feed or end-feed.[38][39] They are commonly made for 10-cm (4-inch) and 15-cm (6-inch) bobbin lengths.[40]
Hand weavers who threw a shuttle could only weave a cloth as wide as their armspan. If cloth needed to be wider, two people would do the task (often this would be an adult with a child). John Kay (1704–1779) patented the flying shuttle in 1733. The weaver held a picking stick that was attached by cords to a device at both ends of the shed. With a flick of the wrist, one cord was pulled and the shuttle was propelled through the shed to the other end with considerable force, speed and efficiency. A flick in the opposite direction and the shuttle was propelled back. A single weaver had control of this motion but the flying shuttle could weave much wider fabric than an arm's length at much greater speeds than had been achieved with the hand thrown shuttle.
The flying shuttle was one of the key developments in weaving that helped fuel the Industrial Revolution. The whole picking motion no longer relied on manual skill and it was just a matter of time before it could be powered by something other than a human.
Different types of power looms are most often defined by the way that the weft, or pick, is inserted into the warp. Many advances in weft insertion have been made in order to make manufactured cloth more cost effective. Weft insertion rate is a limiting factor in production speed. As of 2010[update], industrial looms can weave at 2,000 weft insertions per minute.[41]
There are five main types of weft insertion and they are as follows:
The newest weft thread must be beaten against the fell. Battening can be done with a long stick placed in the shed parallel to the weft (a sword batten), a shorter stick threaded between the warp threads perpendicular to warp and weft (a pin batten), a comb, or a reed (a comb with both ends closed, so that it has to be sleyed, that is have the warp threads threaded through it, when the loom is warped). For rigid-heddle looms, the heddle may be used as a reed.
Patented in 1802, dandy looms automatically rolled up the finished cloth, keeping the fell always the same length. They significantly speeded up hand weaving (still a major part of the textile industry in the 1800s). Similar mechanisms were used in power looms.
The temples act to keep the cloth from shrinking sideways as it is woven. Some warp-weighted looms had temples made of loom weights, suspended by strings so that they pulled the cloth breadthwise.[22] Other looms may have temples tied to the frame, or temples that are hooks with an adjustable shaft between them. Power looms may use temple cylinders. Pins can leave a series of holes in the selvages (these may be from stenter pins used in post-processing).
A power loom is a loom powered by a source of energy other than the weaver's muscles. When power looms were developed, other looms came to be referred to as handlooms. Most cloth is now woven on power looms, but some is still woven on handlooms.[12]
The development of power looms was gradual. The capabilities of power looms gradually expanded, but handlooms remained the most cost-effective way to make some types of textiles for most of the 1800s. Many improvements in loom mechanisms were first applied to hand looms (like the dandy loom), and only later integrated into power looms.
Edmund Cartwright built and patented a power loom in 1785, and it was this that was adopted by the nascent cotton industry in England. The silk loom made by Jacques Vaucanson in 1745 operated on the same principles but was not developed further. The invention of the flying shuttle by John Kay allow a hand weaver to weave broadwoven cloth without an assistant, and was also critical to the development of a commercially successful power loom.[43] Cartwright's loom was impractical but the ideas behind it were developed by numerous inventors in the Manchester area of England where, by 1818, there were 32 factories containing 5,732 looms.[44]
The Horrocks loom was viable, but it was the Roberts Loom in 1830 that marked the turning point.[45][clarification needed] Incremental changes to the three motions continued to be made. The problems of sizing, stop-motions, consistent take-up, and a temple to maintain the width remained. In 1841, Kenworthy and Bullough produced the Lancashire Loom[46] which was self-acting or semi-automatic. This enables a youngster to run six looms at the same time. Thus, for simple calicos, the power loom became more economical to run than the handloom – with complex patterning that used a dobby or Jacquard head, jobs were still put out to handloom weavers until the 1870s. Incremental changes were made such as the Dickinson Loom, culminating in the Keighley-born inventor Northrop, who was working for the Draper Corporation in Hopedale producing the fully automatic Northrop Loom. This loom recharged the shuttle when the pirn was empty. The Draper E and X models became the leading products from 1909. They were challenged by synthetic fibres such as rayon.[47]
By 1942, faster, more efficient, and shuttleless Sulzer and rapier looms had been introduced.[48]
The loom is a symbol of cosmic creation and the structure upon which individual destiny is woven. This symbolism is encapsulated in the classical myth of Arachne who was changed into a spider by the goddess Athena, who was jealous of her skill at the godlike craft of weaving.[49] In Maya civilization the goddess Ixchel taught the first woman how to weave at the beginning of time.[50]