Loading AI tools
Fracturing bedrock by pressurized liquid From Wikipedia, the free encyclopedia
Fracking (also known as hydraulic fracturing, fracing, hydrofracturing, or hydrofracking) is a well stimulation technique involving the fracturing of formations in bedrock by a pressurized liquid. The process involves the high-pressure injection of "fracking fluid" (primarily water, containing sand or other proppants suspended with the aid of thickening agents) into a wellbore to create cracks in the deep-rock formations through which natural gas, petroleum, and brine will flow more freely. When the hydraulic pressure is removed from the well, small grains of hydraulic fracturing proppants (either sand or aluminium oxide) hold the fractures open.[1]
Fracking the Bakken Formation in North Dakota | |
Process type | Mechanical |
---|---|
Industrial sector(s) | Mining |
Main technologies or sub-processes | Fluid pressure |
Product(s) | Natural gas, petroleum |
Inventor | Floyd Farris, Joseph B. Clark (Stanolind Oil and Gas Corporation) |
Year of invention | 1947 |
Hydraulic fracturing began as an experiment in 1947,[2] and the first commercially successful application followed in 1949. As of 2012, 2.5 million "frac jobs" had been performed worldwide on oil and gas wells, over one million of those within the U.S.[3][4] Such treatment is generally necessary to achieve adequate flow rates in shale gas, tight gas, tight oil, and coal seam gas wells.[5] Some hydraulic fractures can form naturally in certain veins or dikes.[6] Drilling and hydraulic fracturing have made the United States a major crude oil exporter as of 2019,[7] but leakage of methane, a potent greenhouse gas, has dramatically increased.[8][9] Increased oil and gas production from the decade-long fracking boom has led to lower prices for consumers, with near-record lows of the share of household income going to energy expenditures.[10][11]
Hydraulic fracturing is highly controversial.[12] Its proponents advocate the economic benefits of more extensively accessible hydrocarbons,[13][14] as well as replacing coal with natural gas, which burns more cleanly and emits less carbon dioxide (CO2),[15][16] and energy independence.[17] Opponents of fracking argue that these are outweighed by the environmental impacts, which include groundwater and surface water contamination,[18] noise and air pollution, and the triggering of earthquakes, along with the resulting hazards to public health and the environment.[19][20] Research has found adverse health effects in populations living near hydraulic fracturing sites,[21][22] including confirmation of chemical, physical, and psychosocial hazards such as pregnancy and birth outcomes, migraine headaches, chronic rhinosinusitis, severe fatigue, asthma exacerbations and psychological stress.[23] Adherence to regulation and safety procedures are required to avoid further negative impacts.[24]
The scale of methane leakage associated with hydraulic fracturing is uncertain, and there is some evidence that leakage may cancel out any greenhouse gas emissions benefit of natural gas relative to other fossil fuels.[25][26]
Increases in seismic activity following hydraulic fracturing along dormant or previously unknown faults are sometimes caused by the deep-injection disposal of hydraulic fracturing flowback (a byproduct of hydraulically fractured wells),[27] and produced formation brine (a byproduct of both fractured and non-fractured oil and gas wells).[28] For these reasons, hydraulic fracturing is under international scrutiny, restricted in some countries, and banned altogether in others.[29][30][31] The European Union is drafting regulations that would permit the controlled application of hydraulic fracturing.[32]
Fracturing rocks at great depth frequently become suppressed by pressure due to the weight of the overlying rock strata and the cementation of the formation. This suppression process is particularly significant in "tensile" (Mode 1) fractures which require the walls of the fracture to move against this pressure. Fracturing occurs when effective stress is overcome by the pressure of fluids within the rock. The minimum principal stress becomes tensile and exceeds the tensile strength of the material.[33][34] Fractures formed in this way are generally oriented in a plane perpendicular to the minimum principal stress, and for this reason, hydraulic fractures in wellbores can be used to determine the orientation of stresses.[35] In natural examples, such as dikes or vein-filled fractures, the orientations can be used to infer past states of stress.[36]
Most mineral vein systems are a result of repeated natural fracturing during periods of relatively high pore fluid pressure. The effect of high pore fluid pressure on the formation process of mineral vein systems is particularly evident in "crack-seal" veins, where the vein material is part of a series of discrete fracturing events, and extra vein material is deposited on each occasion.[37] One example of long-term repeated natural fracturing is in the effects of seismic activity. Stress levels rise and fall episodically, and earthquakes can cause large volumes of connate water to be expelled from fluid-filled fractures. This process is referred to as "seismic pumping".[38]
Minor intrusions in the upper part of the crust, such as dikes, propagate in the form of fluid-filled cracks. In such cases, the fluid is magma. In sedimentary rocks with a significant water content, fluid at fracture tip will be steam.[39]
Fracturing as a method to stimulate shallow, hard rock oil wells dates back to the 1860s. Dynamite or nitroglycerin detonations were used to increase oil and natural gas production from petroleum bearing formations. On 24 April 1865, US Civil War veteran Col. Edward A. L. Roberts received a patent for an "exploding torpedo".[40] It was employed in Pennsylvania, New York, Kentucky, and West Virginia using liquid and also, later, solidified nitroglycerin. Later still the same method was applied to water and gas wells. Stimulation of wells with acid, instead of explosive fluids, was introduced in the 1930s. Due to acid etching, fractures would not close completely resulting in further productivity increase.[41]
Harold Hamm, Aubrey McClendon, Tom Ward and George P. Mitchell are each considered to have pioneered hydraulic fracturing innovations toward practical applications.[42][43]
The relationship between well performance and treatment pressures was studied by Floyd Farris of Stanolind Oil and Gas Corporation. This study was the basis of the first hydraulic fracturing experiment, conducted in 1947 at the Hugoton gas field in Grant County of southwestern Kansas by Stanolind.[5][44] For the well treatment, 1,000 US gallons (3,800 L; 830 imp gal) of gelled gasoline (essentially napalm) and sand from the Arkansas River was injected into the gas-producing limestone formation at 2,400 feet (730 m). The experiment was not very successful as the deliverability of the well did not change appreciably. The process was further described by J.B. Clark of Stanolind in his paper published in 1948. A patent on this process was issued in 1949 and an exclusive license was granted to the Halliburton Oil Well Cementing Company. On 17 March 1949, Halliburton performed the first two commercial hydraulic fracturing treatments in Stephens County, Oklahoma, and Archer County, Texas.[44] Since then, hydraulic fracturing has been used to stimulate approximately one million oil and gas wells[45] in various geologic regimes with good success.
In contrast with large-scale hydraulic fracturing used in low-permeability formations, small hydraulic fracturing treatments are commonly used in high-permeability formations to remedy "skin damage", a low-permeability zone that sometimes forms at the rock-borehole interface. In such cases the fracturing may extend only a few feet from the borehole.[46]
In the Soviet Union, the first hydraulic proppant fracturing was carried out in 1952. Other countries in Europe and Northern Africa subsequently employed hydraulic fracturing techniques including Norway, Poland, Czechoslovakia (before 1989), Yugoslavia (before 1991), Hungary, Austria, France, Italy, Bulgaria, Romania, Turkey, Tunisia, and Algeria.[47]
Massive hydraulic fracturing (also known as high-volume hydraulic fracturing) is a technique first applied by Pan American Petroleum in Stephens County, Oklahoma, US in 1968. The definition of massive hydraulic fracturing varies, but generally refers to treatments injecting over 150 short tons, or approximately 300,000 pounds (136 metric tonnes), of proppant.[48]
American geologists gradually became aware that there were huge volumes of gas-saturated sandstones with permeability too low (generally less than 0.1 millidarcy) to recover the gas economically.[48] Starting in 1973, massive hydraulic fracturing was used in thousands of gas wells in the San Juan Basin, Denver Basin,[49] the Piceance Basin,[50] and the Green River Basin, and in other hard rock formations of the western US. Other tight sandstone wells in the US made economically viable by massive hydraulic fracturing were in the Clinton-Medina Sandstone (Ohio, Pennsylvania, and New York), and Cotton Valley Sandstone (Texas and Louisiana).[48]
Massive hydraulic fracturing quickly spread in the late 1970s to western Canada, Rotliegend and Carboniferous gas-bearing sandstones in Germany, Netherlands (onshore and offshore gas fields), and the United Kingdom in the North Sea.[47]
Horizontal oil or gas wells were unusual until the late 1980s. Then, operators in Texas began completing thousands of oil wells by drilling horizontally in the Austin Chalk, and giving massive slickwater hydraulic fracturing treatments to the wellbores. Horizontal wells proved much more effective than vertical wells in producing oil from tight chalk;[51] sedimentary beds are usually nearly horizontal, so horizontal wells have much larger contact areas with the target formation.[52]
Hydraulic fracturing operations have grown exponentially since the mid-1990s, when technologic advances and increases in the price of natural gas made this technique economically viable.[53]
Hydraulic fracturing of shales goes back at least to 1965, when some operators in the Big Sandy gas field of eastern Kentucky and southern West Virginia started hydraulically fracturing the Ohio Shale and Cleveland Shale, using relatively small fracs. The frac jobs generally increased production, especially from lower-yielding wells.[54]
In 1976, the United States government started the Eastern Gas Shales Project, which included numerous public-private hydraulic fracturing demonstration projects.[55] During the same period, the Gas Research Institute, a gas industry research consortium, received approval for research and funding from the Federal Energy Regulatory Commission.[56]
In 1997, Nick Steinsberger, an engineer of Mitchell Energy (now part of Devon Energy), applied the slickwater fracturing technique, using more water and higher pump pressure than previous fracturing techniques, which was used in East Texas in the Barnett Shale of north Texas.[52] In 1998, the new technique proved to be successful when the first 90 days gas production from the well called S.H. Griffin No. 3 exceeded production of any of the company's previous wells.[57][58] This new completion technique made gas extraction widely economical in the Barnett Shale, and was later applied to other shales, including the Eagle Ford and Bakken Shale.[59][60][61] George P. Mitchell has been called the "father of fracking" because of his role in applying it in shales.[62] The first horizontal well in the Barnett Shale was drilled in 1991, but was not widely done in the Barnett until it was demonstrated that gas could be economically extracted from vertical wells in the Barnett.[52]
As of 2013, massive hydraulic fracturing is being applied on a commercial scale to shales in the United States, Canada, and China. Several additional countries are planning to use hydraulic fracturing.[63][64][65]
According to the United States Environmental Protection Agency (EPA), hydraulic fracturing is a process to stimulate a natural gas, oil, or geothermal well to maximize extraction. The EPA defines the broader process to include acquisition of source water, well construction, well stimulation, and waste disposal.[66]
A hydraulic fracture is formed by pumping fracturing fluid into a wellbore at a rate sufficient to increase pressure at the target depth (determined by the location of the well casing perforations), to exceed that of the fracture gradient (pressure gradient) of the rock.[67] The fracture gradient is defined as pressure increase per unit of depth relative to density, and is usually measured in pounds per square inch, per foot (psi/ft). The rock cracks, and the fracture fluid permeates the rock extending the crack further, and further, and so on. Fractures are localized as pressure drops off with the rate of frictional loss, which is relative to the distance from the well. Operators typically try to maintain "fracture width", or slow its decline following treatment, by introducing a proppant into the injected fluid – a material such as grains of sand, ceramic, or other particulate, thus preventing the fractures from closing when injection is stopped and pressure removed. Consideration of proppant strength and prevention of proppant failure becomes more important at greater depths where pressure and stresses on fractures are higher. The propped fracture is permeable enough to allow the flow of gas, oil, salt water and hydraulic fracturing fluids to the well.[67]
During the process, fracturing fluid leakoff (loss of fracturing fluid from the fracture channel into the surrounding permeable rock) occurs. If not controlled, it can exceed 70% of the injected volume. This may result in formation matrix damage, adverse formation fluid interaction, and altered fracture geometry, thereby decreasing efficiency.[68]
The location of one or more fractures along the length of the borehole is strictly controlled by various methods that create or seal holes in the side of the wellbore. Hydraulic fracturing is performed in cased wellbores, and the zones to be fractured are accessed by perforating the casing at those locations.[69]
Hydraulic-fracturing equipment used in oil and natural gas fields usually consists of a slurry blender, one or more high-pressure, high-volume fracturing pumps (typically powerful triplex or quintuplex pumps) and a monitoring unit. Associated equipment includes fracturing tanks, one or more units for storage and handling of proppant, high-pressure treating iron[clarification needed], a chemical additive unit (used to accurately monitor chemical addition), fracking hose (low-pressure flexible hoses), and many gauges and meters for flow rate, fluid density, and treating pressure.[70] Chemical additives are typically 0.5% of the total fluid volume. Fracturing equipment operates over a range of pressures and injection rates, and can reach up to 100 megapascals (15,000 psi) and 265 litres per second (9.4 cu ft/s; 133 US bbl/min).[71]
A distinction can be made between conventional, low-volume hydraulic fracturing, used to stimulate high-permeability reservoirs for a single well, and unconventional, high-volume hydraulic fracturing, used in the completion of tight gas and shale gas wells. High-volume hydraulic fracturing usually requires higher pressures than low-volume fracturing; the higher pressures are needed to push out larger volumes of fluid and proppant that extend farther from the borehole.[72]
Horizontal drilling involves wellbores with a terminal drillhole completed as a "lateral" that extends parallel with the rock layer containing the substance to be extracted. For example, laterals extend 1,500 to 5,000 feet (460 to 1,520 m) in the Barnett Shale basin in Texas, and up to 10,000 feet (3,000 m) in the Bakken formation in North Dakota. In contrast, a vertical well only accesses the thickness of the rock layer, typically 50–300 feet (15–91 m). Horizontal drilling reduces surface disruptions as fewer wells are required to access the same volume of rock.
Drilling often plugs up the pore spaces at the wellbore wall, reducing permeability at and near the wellbore. This reduces flow into the borehole from the surrounding rock formation, and partially seals off the borehole from the surrounding rock. Low-volume hydraulic fracturing can be used to restore permeability.[73]
The main purposes of fracturing fluid are to extend fractures, add lubrication, change gel strength, and to carry proppant into the formation. There are two methods of transporting proppant in the fluid – high-rate and high-viscosity. High-viscosity fracturing tends to cause large dominant fractures, while high-rate (slickwater) fracturing causes small spread-out micro-fractures.[74]
Water-soluble gelling agents (such as guar gum) increase viscosity and efficiently deliver proppant into the formation.[75]
Fluid is typically a slurry of water, proppant, and chemical additives.[76] Additionally, gels, foams, and compressed gases, including nitrogen, carbon dioxide and air can be injected. Typically, 90% of the fluid is water and 9.5% is sand with chemical additives accounting to about 0.5%.[67][77][78] However, fracturing fluids have been developed using liquefied petroleum gas (LPG) and propane. This process is called waterless fracturing.[79]
When propane is used it is turned into vapor by the high pressure and high temperature. The propane vapor and natural gas both return to the surface and can be collected, making it[clarification needed] easier to reuse and/or resale. None of the chemicals used will return to the surface. Only the propane used will return from what was used in the process.[80]
The proppant is a granular material that prevents the created fractures from closing after the fracturing treatment. Types of proppant include silica sand, resin-coated sand, bauxite, and man-made ceramics. The choice of proppant depends on the type of permeability or grain strength needed. In some formations, where the pressure is great enough to crush grains of natural silica sand, higher-strength proppants such as bauxite or ceramics may be used. The most commonly used proppant is silica sand, though proppants of uniform size and shape, such as a ceramic proppant, are believed to be more effective.[81]
The fracturing fluid varies depending on fracturing type desired, and the conditions of specific wells being fractured, and water characteristics. The fluid can be gel, foam, or slickwater-based. Fluid choices are tradeoffs: more viscous fluids, such as gels, are better at keeping proppant in suspension; while less-viscous and lower-friction fluids, such as slickwater, allow fluid to be pumped at higher rates, to create fractures farther out from the wellbore. Important material properties of the fluid include viscosity, pH, various rheological factors, and others.
Water is mixed with sand and chemicals to create hydraulic fracturing fluid. Approximately 40,000 gallons of chemicals are used per fracturing.[84] A typical fracture treatment uses between 3 and 12 additive chemicals.[67] Although there may be unconventional fracturing fluids, typical chemical additives can include one or more of the following:
The most common chemical used for hydraulic fracturing in the United States in 2005–2009 was methanol, while some other most widely used chemicals were isopropyl alcohol, 2-butoxyethanol, and ethylene glycol.[86]
Typical fluid types are:
For slickwater fluids the use of sweeps is common. Sweeps are temporary reductions in the proppant concentration, which help ensure that the well is not overwhelmed with proppant.[87] As the fracturing process proceeds, viscosity-reducing agents such as oxidizers and enzyme breakers are sometimes added to the fracturing fluid to deactivate the gelling agents and encourage flowback.[75] Such oxidizers react with and break down the gel, reducing the fluid's viscosity and ensuring that no proppant is pulled from the formation. An enzyme acts as a catalyst for breaking down the gel. Sometimes pH modifiers are used to break down the crosslink at the end of a hydraulic fracturing job, since many require a pH buffer system to stay viscous.[87] At the end of the job, the well is commonly flushed with water under pressure (sometimes blended with a friction reducing chemical.) Some (but not all) injected fluid is recovered. This fluid is managed by several methods, including underground injection control, treatment, discharge, recycling, and temporary storage in pits or containers. New technology is continually developing to better handle waste water and improve re-usability.[67]
Measurements of the pressure and rate during the growth of a hydraulic fracture, with knowledge of fluid properties and proppant being injected into the well, provides the most common and simplest method of monitoring a hydraulic fracture treatment. This data along with knowledge of the underground geology can be used to model information such as length, width and conductivity of a propped fracture.[67]
Injection of radioactive tracers along with the fracturing fluid is sometimes used to determine the injection profile and location of created fractures.[88] Radiotracers are selected to have the readily detectable radiation, appropriate chemical properties, and a half life and toxicity level that will minimize initial and residual contamination.[89] Radioactive isotopes chemically bonded to glass (sand) and/or resin beads may also be injected to track fractures.[90] For example, plastic pellets coated with 10 GBq of Ag-110mm may be added to the proppant, or sand may be labelled with Ir-192, so that the proppant's progress can be monitored.[89] Radiotracers such as Tc-99m and I-131 are also used to measure flow rates.[89] The Nuclear Regulatory Commission publishes guidelines which list a wide range of radioactive materials in solid, liquid and gaseous forms that may be used as tracers and limit the amount that may be used per injection and per well of each radionuclide.[90]
A new technique in well-monitoring involves fiber-optic cables outside the casing. Using the fiber optics, temperatures can be measured every foot along the well – even while the wells are being fracked and pumped. By monitoring the temperature of the well, engineers can determine how much hydraulic fracturing fluid different parts of the well use as well as how much natural gas or oil they collect, during hydraulic fracturing operation and when the well is producing.[citation needed]
For more advanced applications, microseismic monitoring is sometimes used to estimate the size and orientation of induced fractures. Microseismic activity is measured by placing an array of geophones in a nearby wellbore. By mapping the location of any small seismic events associated with the growing fracture, the approximate geometry of the fracture is inferred. Tiltmeter arrays deployed on the surface or down a well provide another technology for monitoring strain[91]
Microseismic mapping is very similar geophysically to seismology. In earthquake seismology, seismometers scattered on or near the surface of the earth record S-waves and P-waves that are released during an earthquake event. This allows for motion[clarification needed] along the fault plane to be estimated and its location in the Earth's subsurface mapped. Hydraulic fracturing, an increase in formation stress proportional to the net fracturing pressure, as well as an increase in pore pressure due to leakoff.[clarification needed][92] Tensile stresses are generated ahead of the fracture's tip, generating large amounts of shear stress. The increases in pore water pressure and in formation stress combine and affect weaknesses near the hydraulic fracture, like natural fractures, joints, and bedding planes.[93]
Different methods have different location errors[clarification needed] and advantages. Accuracy of microseismic event mapping is dependent on the signal-to-noise ratio and the distribution of sensors. Accuracy of events located by seismic inversion is improved by sensors placed in multiple azimuths from the monitored borehole. In a downhole array location, accuracy of events is improved by being close to the monitored borehole (high signal-to-noise ratio).
Monitoring of microseismic events induced by reservoir[clarification needed] stimulation has become a key aspect in evaluation of hydraulic fractures, and their optimization. The main goal of hydraulic fracture monitoring is to completely characterize the induced fracture structure, and distribution of conductivity within a formation. Geomechanical analysis, such as understanding a formations material properties, in-situ conditions, and geometries, helps monitoring by providing a better definition of the environment in which the fracture network propagates.[94] The next task is to know the location of proppant within the fracture and the distribution of fracture conductivity. This can be monitored using multiple types of techniques to finally develop a reservoir model than accurately predicts well performance.
Since the early 2000s, advances in drilling and completion technology have made horizontal wellbores much[clarification needed] more economical. Horizontal wellbores allow far greater exposure to a formation than conventional vertical wellbores. This is particularly useful in shale formations which do not have sufficient permeability to produce economically with a vertical well. Such wells, when drilled onshore, are now usually hydraulically fractured in a number of stages, especially in North America. The type of wellbore completion is used to determine how many times a formation is fractured, and at what locations along the horizontal section.[95]
In North America, shale reservoirs such as the Bakken, Barnett, Montney, Haynesville, Marcellus, and most recently the Eagle Ford, Niobrara and Utica shales are drilled horizontally through the producing intervals, completed and fractured.[citation needed] The method by which the fractures are placed along the wellbore is most commonly achieved by one of two methods, known as "plug and perf" and "sliding sleeve".[96]
The wellbore for a plug-and-perf job is generally composed of standard steel casing, cemented or uncemented, set in the drilled hole. Once the drilling rig has been removed, a wireline truck is used to perforate near the bottom of the well, and then fracturing fluid is pumped. Then the wireline truck sets a plug in the well to temporarily seal off that section so the next section of the wellbore can be treated. Another stage is pumped, and the process is repeated along the horizontal length of the wellbore.[97]
The wellbore for the sliding sleeve[clarification needed] technique is different in that the sliding sleeves are included at set spacings in the steel casing at the time it is set in place. The sliding sleeves are usually all closed at this time. When the well is due to be fractured, the bottom sliding sleeve is opened using one of several activation techniques[citation needed] and the first stage gets pumped. Once finished, the next sleeve is opened, concurrently isolating the previous stage, and the process repeats. For the sliding sleeve method, wireline is usually not required.[citation needed]
These completion techniques may allow for more than 30 stages to be pumped into the horizontal section of a single well if required, which is far more than would typically be pumped into a vertical well that had far fewer feet of producing zone exposed.[98]
Hydraulic fracturing is used to increase the rate at which substances such as petroleum or natural gas can be recovered from subterranean natural reservoirs. Reservoirs are typically porous sandstones, limestones or dolomite rocks, but also include "unconventional reservoirs" such as shale rock or coal beds. Hydraulic fracturing enables the extraction of natural gas and oil from rock formations deep below the earth's surface (generally 2,000–6,000 m (5,000–20,000 ft)), which is greatly below typical groundwater reservoir levels. At such depth, there may be insufficient permeability or reservoir pressure to allow natural gas and oil to flow from the rock into the wellbore at high economic return. Thus, creating conductive fractures in the rock is instrumental in extraction from naturally impermeable shale reservoirs. Permeability is measured in the microdarcy to nanodarcy range.[99] Fractures are a conductive path connecting a larger volume of reservoir to the well. So-called "super fracking" creates cracks deeper in the rock formation to release more oil and gas, and increases efficiency.[100] The yield for typical shale bores generally falls off after the first year or two, but the peak producing life of a well can be extended to several decades.[101]
While the main industrial use of hydraulic fracturing is in stimulating production from oil and gas wells,[102][103][104] hydraulic fracturing is also applied:
Since the late 1970s, hydraulic fracturing has been used, in some cases, to increase the yield of drinking water from wells in a number of countries, including the United States, Australia, and South Africa.[113][114][115]
Hydraulic fracturing has been seen as one of the key methods of extracting unconventional oil and unconventional gas resources. According to the International Energy Agency, the remaining technically recoverable resources of shale gas are estimated to amount to 208 trillion cubic metres (7,300 trillion cubic feet), tight gas to 76 trillion cubic metres (2,700 trillion cubic feet), and coalbed methane to 47 trillion cubic metres (1,700 trillion cubic feet). As a rule, formations of these resources have lower permeability than conventional gas formations. Therefore, depending on the geological characteristics of the formation, specific technologies such as hydraulic fracturing are required. Although there are also other methods to extract these resources, such as conventional drilling or horizontal drilling, hydraulic fracturing is one of the key methods making their extraction economically viable. The multi-stage fracturing technique has facilitated the development of shale gas and light tight oil production in the United States and is believed to do so in the other countries with unconventional hydrocarbon resources.[13]
A large majority of studies indicate that hydraulic fracturing in the United States has had a strong positive economic benefit so far.[citation needed] The Brookings Institution estimates that the benefits of Shale Gas alone has led to a net economic benefit of $48 billion per year. Most of this benefit is within the consumer and industrial sectors due to the significantly reduced prices for natural gas.[116] Other studies have suggested that the economic benefits are outweighed by the externalities and that the levelized cost of electricity (LCOE) from less carbon and water intensive sources is lower.[117]
The primary benefit of hydraulic fracturing is to offset imports of natural gas and oil, where the cost paid to producers otherwise exits the domestic economy.[118] However, shale oil and gas is highly subsidised in the US, and has not yet covered production costs[119] – meaning that the cost of hydraulic fracturing is paid for in income taxes, and in many cases is up to double the cost paid at the pump.[120]
Research suggests that hydraulic fracturing wells have an adverse effect on agricultural productivity in the vicinity of the wells.[121] One paper found "that productivity of an irrigated crop decreases by 5.7% when a well is drilled during the agriculturally active months within 11–20 km radius of a producing township. This effect becomes smaller and weaker as the distance between township and wells increases."[121] The findings imply that the introduction of hydraulic fracturing wells to Alberta cost the province $14.8 million in 2014 due to the decline in the crop productivity,[121]
The Energy Information Administration of the US Department of Energy estimates that 45% of US gas supply will come from shale gas by 2035 (with the vast majority of this replacing conventional gas, which has a lower greenhouse-gas footprint).[122]
An anti-fracking movement has emerged both internationally with involvement of international environmental organizations and nations such as France and locally in affected areas such as Balcombe in Sussex where the Balcombe drilling protest was in progress during mid-2013.[123] The considerable opposition against hydraulic fracturing activities in local townships in the United States has led companies to adopt a variety of public relations measures to reassure the public, including the employment of former military personnel with training in psychological warfare operations. According to Matt Pitzarella, the communications director at Range Resources, employees trained in the Middle East have been valuable to Range Resources in Pennsylvania, when dealing with emotionally charged township meetings and advising townships on zoning and local ordinances dealing with hydraulic fracturing.[124][125]
There have been many protests directed at hydraulic fracturing. For example, ten people were arrested in 2013 during an anti-fracking protest near New Matamoras, Ohio, after they illegally entered a development zone and latched themselves to drilling equipment.[126] In northwest Pennsylvania, there was a drive-by shooting at a well site, in which someone shot two rounds of a small-caliber rifle in the direction of a drilling rig.[127] In Washington County, Pennsylvania, a contractor working on a gas pipeline found a pipe bomb that had been placed where a pipeline was to be constructed, which local authorities said would have caused a "catastrophe" had they not discovered and detonated it.[128]
The United States Department of State established the Global Shale Gas Initiative to persuade governments around the world to give concessions to the major oil and gas companies to set up fracking operations. A document from the United States diplomatic cables leak show that, as part of this project, U.S. officials convened conferences for foreign government officials that featured presentations by major oil and gas company representatives and by public relations professionals with expertise on how to assuage populations of target countries whose citizens were often quite hostile to fracking on their lands. The US government project succeeded as many countries on several continents acceded to the idea of granting concessions for fracking; Poland, for example, agreed to permit fracking by the major oil and gas corporations on nearly a third of its territory.[129] The US Export-Import Bank, an agency of the US government, provided $4.7 billion in financing for fracking operations set up since 2010 in Queensland, Australia.[130]
In 2014 a number of European officials suggested that several major European protests against hydraulic fracturing (with mixed success in Lithuania and Ukraine) may be partially sponsored by Gazprom, Russia's state-controlled gas company. The New York Times suggested that Russia saw its natural gas exports to Europe as a key element of its geopolitical influence, and that this market would diminish if hydraulic fracturing is adopted in Eastern Europe, as it opens up significant shale gas reserves in the region. Russian officials have on numerous occasions made public statements to the effect that hydraulic fracturing "poses a huge environmental problem".[131]
Hydraulic fracturing is currently taking place in the United States in Arkansas, California, Colorado, Louisiana, North Dakota, Oklahoma, Pennsylvania, Texas, Virginia, West Virginia,[132] and Wyoming. Other states, such as Alabama, Indiana, Michigan, Mississippi, New Jersey, New York, and Ohio, are either considering or preparing for drilling using this method. Maryland[133] and Vermont have permanently banned hydraulic fracturing, and New York and North Carolina have instituted temporary bans. New Jersey currently has a bill before its legislature to extend a 2012 moratorium on hydraulic fracturing that recently expired. Although a hydraulic fracturing moratorium was recently lifted in the United Kingdom, the government is proceeding cautiously because of concerns about earthquakes and the environmental effect of drilling. Hydraulic fracturing is currently banned in France and Bulgaria.[53]
Josh Fox's 2010 Academy Award nominated film Gasland[134] became a center of opposition to hydraulic fracturing of shale. The movie presented problems with groundwater contamination near well sites in Pennsylvania, Wyoming and Colorado.[135] Energy in Depth, an oil and gas industry lobbying group, called the film's facts into question.[136] In response, a rebuttal of Energy in Depth's claims of inaccuracy was posted on Gasland's website.[137] The Director of the Colorado Oil and Gas Conservation Commission (COGCC) offered to be interviewed as part of the film if he could review what was included from the interview in the final film but Fox declined the offer.[138] ExxonMobil, Chevron Corporation and ConocoPhillips aired advertisements during 2011 and 2012 that claimed to describe the economic and environmental benefits of natural gas and argue that hydraulic fracturing was safe.[139]
The 2012 film Promised Land, starring Matt Damon, takes on hydraulic fracturing.[140] The gas industry countered the film's criticisms of hydraulic fracturing with flyers, and Twitter and Facebook posts.[139]
In January 2013, Northern Irish journalist and filmmaker Phelim McAleer released a crowdfunded[141] documentary called FrackNation as a response to the statements made by Fox in Gasland, claiming it "tells the truth about fracking for natural gas". FrackNation premiered on Mark Cuban's AXS TV. The premiere corresponded with the release of Promised Land.[142]
In April 2013, Josh Fox released Gasland 2, his "international odyssey uncovering a trail of secrets, lies and contamination related to hydraulic fracking". It challenges the gas industry's portrayal of natural gas as a clean and safe alternative to oil as a myth, and that hydraulically fractured wells inevitably leak over time, contaminating water and air, hurting families, and endangering the Earth's climate with the potent greenhouse gas methane.
In 2014, Scott Cannon of Video Innovations released the documentary The Ethics of Fracking. The film covers the politics, spiritual, scientific, medical and professional points of view on hydraulic fracturing. It also digs into the way the gas industry portrays hydraulic fracturing in their advertising.[143]
In 2015, the Canadian documentary film Fractured Land had its world premiere at the Hot Docs Canadian International Documentary Festival.[144]
Typically the funding source of the research studies is a focal point of controversy. Concerns have been raised about research funded by foundations and corporations, or by environmental groups, which can at times lead to at least the appearance of unreliable studies.[145][146] Several organizations, researchers, and media outlets have reported difficulty in conducting and reporting the results of studies on hydraulic fracturing due to industry[147] and governmental pressure,[29] and expressed concern over possible censoring of environmental reports.[147][148][149] Some have argued there is a need for more research into the environmental and health effects of the technique.[150][151][152][153]
There is concern over the possible adverse public health implications of hydraulic fracturing activity.[150] A 2013 review on shale gas production in the United States stated, "with increasing numbers of drilling sites, more people are at risk from accidents and exposure to harmful substances used at fractured wells."[154] A 2011 hazard assessment recommended full disclosure of chemicals used for hydraulic fracturing and drilling as many have immediate health effects, and many may have long-term health effects.[155]
In June 2014 Public Health England published a review of the potential public health impacts of exposures to chemical and radioactive pollutants as a result of shale gas extraction in the UK, based on the examination of literature and data from countries where hydraulic fracturing already occurs.[151] The executive summary of the report stated: "An assessment of the currently available evidence indicates that the potential risks to public health from exposure to the emissions associated with shale gas extraction will be low if the operations are properly run and regulated. Most evidence suggests that contamination of groundwater, if it occurs, is most likely to be caused by leakage through the vertical borehole. Contamination of groundwater from the underground hydraulic fracturing process itself (i.e. the fracturing of the shale) is unlikely. However, surface spills of hydraulic fracturing fluids or wastewater may affect groundwater, and emissions to air also have the potential to impact on health. Where potential risks have been identified in the literature, the reported problems are typically a result of operational failure and a poor regulatory environment."[151]: iii
A 2012 report prepared for the European Union Directorate-General for the Environment identified potential risks to humans from air pollution and ground water contamination posed by hydraulic fracturing.[156] This led to a series of recommendations in 2014 to mitigate these concerns.[157][158] A 2012 guidance for pediatric nurses in the US said that hydraulic fracturing had a potential negative impact on public health and that pediatric nurses should be prepared to gather information on such topics so as to advocate for improved community health.[159]
A 2017 study in The American Economic Review found that "additional well pads drilled within 1 kilometer of a community water system intake increases shale gas-related contaminants in drinking water."[160]
A 2022 study conduced by Harvard T.H. Chan School of Public Health and published in Nature Energy found that elderly people living near or downwind of unconventional oil and gas development (UOGD) -- which involves extraction methods including fracking—are at greater risk of experiencing early death compared with elderly persons who don't live near such operations.[161]
Statistics collected by the U.S. Department of Labor and analyzed by the U.S. Centers for Disease Control and Prevention show a correlation between drilling activity and the number of occupational injuries related to drilling and motor vehicle accidents, explosions, falls, and fires.[162] Extraction workers are also at risk for developing pulmonary diseases, including lung cancer and silicosis (the latter because of exposure to silica dust generated from rock drilling and the handling of sand).[163] The U.S. National Institute for Occupational Safety and Health (NIOSH) identified exposure to airborne silica as a health hazard to workers conducting some hydraulic fracturing operations.[164] NIOSH and OSHA issued a joint hazard alert on this topic in June 2012.[164]
Additionally, the extraction workforce is at increased risk for radiation exposure. Fracking activities often require drilling into rock that contains naturally occurring radioactive material (NORM), such as radon, thorium, and uranium.[165]
Another report done by the Canadian Medical Journal reported that after researching they identified 55 factors that may cause cancer, including 20 that have been shown to increase the risk of leukemia and lymphoma. The Yale Public Health analysis warns that millions of people living within a mile of fracking wells may have been exposed to these chemicals.[166]
![]() Schematic depiction of hydraulic fracturing for shale gas | |
Process type | Mechanical |
---|---|
Industrial sector(s) | Mining |
Main technologies or sub-processes | Fluid pressure |
Product(s) | Natural gas, petroleum |
Inventor | Floyd Farris, Joseph B. Clark (Stanolind Oil and Gas Corporation) |
Year of invention | 1947 |
The potential environmental effects of hydraulic fracturing include air emissions and climate change, high water consumption, groundwater contamination, land use,[167] risk of earthquakes, noise pollution, and various health effects on humans.[168] Air emissions are primarily methane that escapes from wells, along with industrial emissions from equipment used in the extraction process.[156] Modern UK and EU regulation requires zero emissions of methane, a potent greenhouse gas.[citation needed] Escape of methane is a bigger problem in older wells than in ones built under more recent EU legislation.[156]
In December 2016 the United States Environmental Protection Agency (EPA) issued the "Hydraulic Fracturing for Oil and Gas: Impacts from the Hydraulic Fracturing Water Cycle on Drinking Water Resources in the United States (Final Report)." The EPA found scientific evidence that hydraulic fracturing activities can impact drinking water resources.[169] A few of the main reasons why drinking water can be contaminated according to the EPA are:
The lifecycle greenhouse gas emissions of shale oil are 21%-47% higher than those of conventional oil, while emissions from unconventional gas are from 6% lower to 43% higher than the emissions of conventional gas.[170]
Hydraulic fracturing uses between 1.2 and 3.5 million US gallons (4,500 and 13,200 m3) of water per well, with large projects using up to 5 million US gallons (19,000 m3).[171] Additional water is used when wells are refractured.[75][172] An average well requires 3 to 8 million US gallons (11,000 to 30,000 m3) of water over its lifetime.[67] According to the Oxford Institute for Energy Studies, greater volumes of fracturing fluids are required in Europe, where the shale depths average 1.5 times greater than in the U.S.[173] Surface water may be contaminated through spillage and improperly built and maintained waste pits,[174] and ground water can be contaminated if the fluid is able to escape the formation being fractured (through, for example, abandoned wells, fractures, and faults[175]) or by produced water (the returning fluids, which also contain dissolved constituents such as minerals and brine waters). The possibility of groundwater contamination from brine and fracturing fluid leakage through old abandoned wells is low.[176][151] Produced water is managed by underground injection, municipal and commercial wastewater treatment and discharge, self-contained systems at well sites or fields, and recycling to fracture future wells.[177] Typically less than half of the produced water used to fracture the formation is recovered.[178]
In the United States over 12 million acres are being used for fossil fuels. About 3.6 hectares (8.9 acres) of land is needed per each drill pad for surface installations. This is equivalent of six Yellowstone National Parks.[179] Well pad and supporting structure construction significantly fragments landscapes which likely has negative effects on wildlife.[180] These sites need to be remediated after wells are exhausted.[156] Research indicates that effects on ecosystem services costs (i.e., those processes that the natural world provides to humanity) has reached over $250 million per year in the U.S.[181] Each well pad (in average 10 wells per pad) needs during preparatory and hydraulic fracturing process about 800 to 2,500 days of noisy activity, which affect both residents and local wildlife. In addition, noise is created by continuous truck traffic (sand, etc.) needed in hydraulic fracturing.[156] Research is underway to determine if human health has been affected by air and water pollution, and rigorous following of safety procedures and regulation is required to avoid harm and to manage the risk of accidents that could cause harm.[151]
In July 2013, the US Federal Railroad Administration listed oil contamination by hydraulic fracturing chemicals as "a possible cause" of corrosion in oil tank cars.[182]
Hydraulic fracturing has been sometimes linked to induced seismicity or earthquakes.[183] The magnitude of these events is usually too small to be detected at the surface, although tremors attributed to fluid injection into disposal wells have been large enough to have often been felt by people, and to have caused property damage and possibly injuries.[27][184][185][186][187][188] A U.S. Geological Survey reported that up to 7.9 million people in several states have a similar earthquake risk to that of California, with hydraulic fracturing and similar practices being a prime contributing factor.[189]
Microseismic events are often used to map the horizontal and vertical extent of the fracturing.[91] A better understanding of the geology of the area being fracked and used for injection wells can be helpful in mitigating the potential for significant seismic events.[190]
People obtain drinking water from either surface water, which includes rivers and reservoirs, or groundwater aquifers, accessed by public or private wells. There are already a host of documented instances in which nearby groundwater has been contaminated by fracking activities, requiring residents with private wells to obtain outside sources of water for drinking and everyday use.[191][192]
Per- and polyfluoroalkyl substances also known as "PFAS" or "forever chemicals" have been linked to cancer and birth defects. The chemicals used in fracking stay in the environment. Once there those chemicals will eventually break down into PFAS. These chemicals can escape from drilling sites and into the groundwater. PFAS are able to leak into underground wells that store million gallons of wastewater.[193]
Despite these health concerns and efforts to institute a moratorium on fracking until its environmental and health effects are better understood, the United States continues to rely heavily on fossil fuel energy. In 2017, 37% of annual U.S. energy consumption is derived from petroleum, 29% from natural gas, 14% from coal, and 9% from nuclear sources, with only 11% supplied by renewable energy, such as wind and solar power.[194]
In 2022 the USA experienced a fracking boom, when the war in Ukraine led to a massive increase in approval of new drillings. Planned drillings will release 140 billion tons of carbon, 4 times more that the annual global emissions.[195]
Countries using or considering use of hydraulic fracturing have implemented different regulations, including developing federal and regional legislation, and local zoning limitations.[196][197] In 2011, after public pressure France became the first nation to ban hydraulic fracturing, based on the precautionary principle as well as the principle of preventive and corrective action of environmental hazards.[30][31][198][199] The ban was upheld by an October 2013 ruling of the Constitutional Council.[200] Some other countries such as Scotland have placed a temporary moratorium on the practice due to public health concerns and strong public opposition.[201] Countries like England and South Africa have lifted their bans, choosing to focus on regulation instead of outright prohibition.[202][203] Germany has announced draft regulations that would allow using hydraulic fracturing for the exploitation of shale gas deposits with the exception of wetland areas.[204] In China, regulation on shale gas still faces hurdles, as it has complex interrelations with other regulatory regimes, especially trade.[205] Many states in Australia have either permanently or temporarily banned fracturing for hydrocarbons.[citation needed] In 2019, hydraulic fracturing was banned in UK.[206]
The European Union has adopted a recommendation for minimum principles for using high-volume hydraulic fracturing.[32] Its regulatory regime requires full disclosure of all additives.[207] In the United States, the Ground Water Protection Council launched FracFocus.org, an online voluntary disclosure database for hydraulic fracturing fluids funded by oil and gas trade groups and the U.S. Department of Energy.[208][209] Hydraulic fracturing is excluded from the Safe Drinking Water Act's underground injection control's regulation, except when diesel fuel is used. The EPA assures surveillance of the issuance of drilling permits when diesel fuel is employed.[210]
In 2012, Vermont became the first state in the United States to ban hydraulic fracturing. On 17 December 2014, New York became the second state to issue a complete ban on any hydraulic fracturing due to potential risks to human health and the environment.[211][212][213]