Fire brick

"Firebrick" redirects here. For the communities in the United States, see Firebrick, Ohio and Firebrick, Kentucky.

A fire brick, firebrick, fireclay brick, or refractory brick is a block of ceramic material used in lining furnaces, kilns, fireboxes, and fireplaces. A refractory brick is built primarily to withstand high temperature, but will also usually have a low thermal conductivity for greater energy efficiency. Usually dense fire bricks are used in applications with extreme mechanical, chemical, or thermal stresses, such as the inside of a wood-fired kiln or a furnace, which is subject to abrasion from wood, fluxing from ash or slag, and high temperatures. In other, less harsh situations, such as in an electric or natural gas fired kiln, more porous bricks, commonly known as "kiln bricks", are a better choice.^[1] They are weaker, but they are much lighter and easier to form and insulate far better than dense bricks. In any case, firebricks should not spall, and their strength should hold up well during rapid temperature changes.

Refractory bricks in a torpedo car used for hauling molten iron

Manufacture

In the making of firebrick, fire clay is fired in the kiln until it is partly vitrified. For special purposes, the brick may also be glazed. There are two standard sizes of fire brick: 9 in × 4+1⁄2 in × 3 in (229 mm × 114 mm × 76 mm) and 9 in × 4+1⁄2 in × 2+1⁄2 in (229 mm × 114 mm × 64 mm).^[2] Also available are firebrick "splits" which are half the thickness and are often used to line wood stoves and fireplace inserts. The dimensions of a split are usually 9 in × 4+1⁄2 in × 1+1⁄4 in (229 mm × 114 mm × 32 mm).^[3] Fire brick was first invented in 1822 by William Weston Young in the Neath Valley of Wales.

High temperature applications

The silica fire bricks that line steel-making furnaces are used at temperatures up to 3,000 °F (1,649 °C), which would melt many other types of ceramic, and in fact part of the silica firebrick liquefies.^{[citation needed]} High-temperature Reusable Surface Insulation (HRSI), a material with the same composition, was used in the insulating tiles of the Space Shuttle.^{[citation needed]}

Non-ferrous metallurgical processes use basic refractory bricks because the slags used in these processes readily dissolve the "acidic" silica bricks.^[4] The most common basic refractory bricks used in smelting non-ferrous metal concentrates are "chrome-magnesite" or "magnesite-chrome" bricks (depending on the relative ratios of magnesite and chromite ores used in their manufacture).^[5]

Lower temperature applications

A range of other materials find use as firebricks for lower temperature applications.^[6] Magnesium oxide is often used as a lining for furnaces. Silica bricks are the most common type of bricks used for the inner lining of furnaces and incinerators. As the inner lining is usually of sacrificial nature, fire bricks of higher alumina content may be employed to lengthen the duration between re-linings. Very often cracks can be seen in this sacrificial inner lining shortly after being put into operation. They revealed more expansion joints should have been put in the first place, but these now become expansion joints themselves and are of no concern as long as structural integrity is not affected.^[7] Silicon carbide, with high abrasive strength, is a popular material for hearths of incinerators and cremators. Common red clay brick may be used for chimneys and wood-fired ovens.

Potential use to store energy

Firebricks, with their ability to withstand high temperatures and store heat, offer a promising solution for storing energy. These refractory bricks can be used to store industrial process heat, leveraging excess renewable electricity to create a low-cost, continuous heat source for industry. Due to their construction from common materials, firebrick storage systems are much more cost-effective than battery systems for thermal energy storage. Research across 149 countries indicates that using firebricks for heat storage can significantly reduce the need for electricity generation, battery storage, hydrogen production, and low-temperature heat storage. This approach could lower overall energy costs by about 1.8%, making firebricks a valuable tool in reducing the costs of transitioning to 100% clean, renewable energy. ^[8]

See also

• Harbison-Walker Refractories Company
• Equivalent VIII
• Niles Firebrick

References

1. "Insulating fire bricks". Retrieved 2016-08-07.
2. "Refractory Fire Bricks | Kiln Building Fire Brick". www.sheffield-pottery.com. Retrieved 2020-07-18.
3. "Refractory Fire Bricks | Kiln Building Fire Brick". www.sheffield-pottery.com. Retrieved 2020-07-18.
4. Modern Refractory Practice, Fifth Edition (Harbison–Walker Refractories: Pittsburgh, Pennsylvania, 1992), Page CR-2
5. Modern Refractory Practice, Fifth Edition (Harbison–Walker Refractories: Pittsburgh, Pennsylvania, 1992), Page CR-3
6. "Firebricks High Temperature Resistant". www.vitcas.com. Retrieved 2023-06-21.
7. Refractory Engineering. Die Deutsche Bibliothek. 2004. ISBN 3-8027-3155-7.
8. Jacobson, Mark Z; Sambor, Daniel J; Fan, Yuanbei F; Mühlbauer, Andreas (2024). "Effects of firebricks for industrial process heat on the cost of matching all-sector energy demand with 100% wind–water–solar supply in 149 countries". PNAS Nexus. 3 (7): pgae274. doi:10.1093/pnasnexus/pgae274. PMC 11263865.

Further reading

• Burton, Joseph; Burton, William (1911). "Firebrick" . In Chisholm, Hugh (ed.). Encyclopædia Britannica. Vol. 10 (11th ed.). Cambridge University Press. pp. 418–419.