Remove ads
The China Railways JF4 (解放4, Jiěfàng, "liberation") class steam locomotive was a class of superheated 2-8-2 steam locomotives for goods trains operated by the China Railway. They were originally built for the South Manchuria Railway (Mantetsu) in Japan in 1935.
| China Railways JF4 (解放4) Mantetsu Mikashi class (ミカシ) | |||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
 Builder's photo of ミカシ1661, built by Kisha Seizō in 1935 | |||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||
After a number of incidents involving broken crankshafts in the Mikani class locomotives, as well as needing more motive power to meet the increase in goods traffic following the establishment of Manchukuo, the Mikashi class was designed in 1933[1] and put into production in 1935, with fifteen built in Japan that year, four by Kisha Seizō and eleven by Kawasaki.
As the three-cylinder design of the Mikani class was deemed too complex, the Mikashi class returned to the proven two-cylinder layout. In order to achieve a tractive effort equal to or greater than that of the three-cylinder locomotives with a two-cylinder engine, it is necessary to increase the adhesive weight of the locomotive; however, this would make the axle load unacceptably high - between 24.0 t (23.6 long tons) and 25.6 t (25.2 long tons). To overcome this, a limited cutoff system was adopted with a maximum cutoff of 50%; by balancing the rotational forces of the left and right cylinders, the axle load was successfully limited to 23.0 t (22.6 long tons).
Boiler pressure was increased from 12.7 to 17.0 kgf/cm2 (181 to 242 psi; 1,245 to 1,667 kPa), whilst other new features included a Schmidt type E superheater, a feedwater heater and a combustion chamber firebox. Fuel consumption was also improved, with the Mikashi class using from 10% to up to 22.6% less coal than the Mikani class. The wheel diameter was also increased from 1,370 to 1,500 mm (53.94 to 59.06 in) in order to increase the speed of goods trains, however as this could result in wheel slippage on steeper sections due to the reduction in piston speed, so the timetables of goods trains were adjusted accordingly. Used primarily on heavy goods trains between Fengtian and Dalian to transport coal from the Fushun Coal Mine to port, they could pull up to sixty 30 t (30 long tons; 33 short tons) coal hoppers.
| Owner | Class & numbers (1935–1938) | Class & numbers (1938–1945) | Builder | Year |
|---|---|---|---|---|
| Mantetsu | ミカシ1650–ミカシ1660 | ミカシ1–ミカシ11 | Kawasaki | 1935 |
| Mantetsu | ミカシ1661–ミカシ1664 | ミカシ12–ミカシ15 | Kisha Seizō | 1935 |
Remove ads
At the end of the Pacific War, the 15 Mikashi class locomotives were divided between the Dalian (13) and the Fengtian (2) depots, and all were taken over by the Republic of China Railway. Following the establishment of the People's Republic and the subsequent creation of the current China Railway, they became class ㄇㄎ肆 (MK4) in 1951, and class 解放4 (JF4, jiěfàng, "liberation") in 1959 and numbered 2701–2715. As during the Mantetsu times, they were primarily used around Dalian and Shenyang (formerly Fengtian).
Remove ads
Wikiwand in your browser!
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.
Remove ads