Loading AI tools
Blu-Ray Disc that can be written to once with an optical disc recorder From Wikipedia, the free encyclopedia
Blu-ray Disc Recordable (BD-R) and Blu-ray Disc Recordable Erasable (BD-RE) refer to two direct to disc optical disc recording technologies that can be recorded on to a Blu-ray-based optical disc with an optical disc recorder. BD-R discs can only be written to once, whereas BD-RE discs can be erased and re-recorded multiple times, similar to CD-R and CD-RW for a compact disc (CD). Disc capacities are 25 GB for single-layer discs, 50 GB for double-layer discs,[1] 100 GB ("XL") for triple-layer, and 128 GB for quadruple-layer (in BD-R only).[2][3]
.JPG)
The minimum speed at which a Blu-ray Disc can be written is 36 megabits (4.5 megabytes) per second.[4]
As of 2024, one of the primary pioneers of the Blu-ray disc, Sony, is winding down production of recordable Blu-ray discs in its plant in Tagajo, Japan. Sony plans to gradually cease its manufacturing of optical media, including recordable Blu-ray discs.[5]
As of November 2022[update], there are five versions of BD-RE and four versions of BD-R formats. Each version includes three Parts (a.k.a. Books): Basic Format Specifications, File System Specifications, Audio Visual Basic Specifications. Each part has sub-versions (e.g. R2 Format Specification includes Part 3: Audio Visual Basic Specifications Ver.3.02, Part 2: File System Specifications Ver. 1.11, Part 1: Basic Format Specifications Ver. 1.3).[6][7][8]
| Date | RE Version | R Version | By Parts[8][a] | Changes | ||
|---|---|---|---|---|---|---|
| Part 1 | Part 2 | Part 3 | ||||
| 2002 | 1.0[9] | RE V1.0 | RE V1.0 | RE V1.0 | ||
| 2005 | 2.0[12] | 1.0 | RE V2.1 R V1.3 | RE V2.1 R V1.1 | RE V2.1 | |
| September 2006 | 3.0[16] | 2.0[6] | RE V2.1 R V1.3 | RE V2.1 R V1.1 | RE V3.0 + ROM V2.4 (BDMV) |
|
| June 2010 | 4.0[17] | 3.0[18] | RE V3.0 R V2.0 | RE V3.0 R V2.0 | RE V4.0 + RE V2.1 |
New BDXL definition:
|
| December 2017 | 5.0[20] | 4.0[21] | RE V3.1 R V2.2 | RE V4.0 R V3.0 | RE V5.0 | BDXL expansions:
|
Inspite of having the "Blu-ray" brand, "BDXL" is separate from the original "BD" format, meaning existing Blu-ray drives that predate the release of BDXL (mid-2010) do not support BDXL. Even Blu-ray drives released after then do not necessarily support BDXL unless explicitly stated.[22]
As of December 2017[update], the following speeds are seen in Blu-Ray specifications for R/RE discs:[8]
| Drive speed | Data rate | 25 GB BD-R(E) write time | 50 GB BD-R(E) DL (25 GB/layer) write time | 100 GB BD-R(E) XL TL (~33 GB/layer) write time | ||
|---|---|---|---|---|---|---|
| 1×[1] | 36 Mbit/s | 4.5 MB/s | 4.29 MiB/s | ~95 min. | ~190 min. | ~380 min. |
| 2× | 72 Mbit/s | 9 MB/s | 8.58 MiB/s | ~47 min. | ~94 min. | ~188 min. |
| 4× | 144 Mbit/s | 18 MB/s | 17.17 MiB/s | ~24 min. | ~48 min. | ~96 min. |
| 6× | 216 Mbit/s | 27 MB/s | 25.75 MiB/s | ~16 min. | ~32 min. | ~64 min. |
| 8× | 288 Mbit/s | 36 MB/s | ~34.32 MiB/s | ~11.25 min. | ~22.5 min. | ~45 min. |
| 10× | 360 Mbit/s | 45 MB/s | 42.898 MiB/s | ~9 min. | ~18 min. | ~36 min. |
| 12× | 432 Mbit/s | 54 MB/s | ~51.48 MiB/s | ~7.5 min. | ~15 min. | ~30 min. |
| 14× | 504 Mbit/s | 63 MB/s | ~60 MiB/s | ~6.5 min. | ~13 min. | ~26 min. |
| 16× | 576 Mbit/s | 72 MB/s | ~68.64 MiB/s | ~5.7 min. | ~11.5 min. | ~23 min. |
2× speeds are mandatory for all formats, with 4× and 6× being optional for non-XL BD-R media. Since BD-RE 5.0/BD-R 4.0, a read speed of 4× is mandatory for UHD support.[8]
Note: If write verification is enabled, as it may be by default on some burning software, the write will take longer to complete. Erasing a BD-RE is not necessary since existing data can be directly overwritten. Unlike with CD-RW, there is no need for blanking BD-RE before re-use, but they need to be formatted before first use. Burn programs may detect the unformatted state and automatically format the medium before beginning to write.[23]
Write verification is a feature of formatted Blu-ray media, officially called "Defect Management". Similar functionality existed on DVD-RAM and on Mount Rainer-supporting disc drives, but BD-R is the first write-once media with such functionality. If not deactivated, the correctness of the written data is verified immediately after being written. Poorly readable data can be written again to an area of spare blocksm and, the writing speed is halved because only half of the disc rotations are for writing. Defect management can be deactivated by burn programs using a feature called "Stream Recording" which enables full nominal write speed. Whether defect management is beneficial with mediocre media depends much on the individual medium and the drive's firmware. It works well with narrowly located bad spots but tends to fail more often than stream recording if the drive perceives reduced read quality on the whole medium. It may be desirable to deactivate write verification on undamaged media to save time when mass-producing physical copies of data, since errors are unlikely to occur on physically undamaged media.[24][25]
As of April 2018[update] (approximate pricing):
Instead of the pits and lands found on prepressed/prerecorded/replicated discs, BD-R and RE discs contain grooves which contain a wobble frequency that is used to locate the position of the reading or writing laser on the disc.[34] BD-R has an Optimum Power Calibrations (OPC) / Test Zone, which is used to calibrate (finely adjust) the power of the writing laser before and during writing, and it also has a Drive Calibration Zone (DCZ) at the outer edge of the disc, for optional high speed calibration. The calibration is necessary to allow for slight manufacturing defects, greatly reducing or completely eliminating rejected discs and drives, reducing costs and eliminating potential waste. The information below describes the different types of recording layers that may be used on BD-R and BD-RE discs.
"Normal" BD-R discs use a composite (or, in the case of BD-RE, a phase-changing alloy) that decreases its reflectivity on recording, i.e. "High To Low".[35] Sony, for example, uses an inorganic[36] composite that splits into two laminar components with low reflectivity.[37] Composites used may include BiN, Ge3N4, and Pd-doped tellurium suboxide.[38] A pair of layers with copper alloy and silicon that combines on recording may alternatively be used.[39] Similar to CD-RW and DVD-RW, a phase transition alloy (often GeSbTe or InAgTeSb; copper silicate (CuSi) or other alloys can also be used, like Verbatim's proprietary MABL)[40][39][41] is used for BD-RE discs. Melting the material with a very high power beam turns it into an amorphous state with low reflectivity, while heating at a lower power erases it back to a crystalline state with high reflectivity.[42]
In BD-RE discs, the data layers are surrounded by a pair of dielectric Zinc Sulfur-Silicon Dioxide layers.[3][43] An adhesive spacer layer and a semi-reflective layer are used for multi-layer discs.[39][44] The recording and dielectric layers are all deposited using Sputtering.[43] On multi-layer BD-RE discs, each GeSbTe recording layer is progressively thinner. So the first layer (L0) is 10 nm thick, L1 is 7.5 nm thick, L2 is 6 nm thick, and so on. The silver alloy reflective layers that are behind each recording layer also become progressively thinner, so the L0 silver layer is 10 nm thick, the L1 layer is 9 nm thick, the L2 layer is 7 nm thick, and so on. The separation layers that separate the recording layers from one another also progressively become thinner.[45][46]
BD-R LTH is a write-once Blu-ray Disc format that features an organic dye recording layer. "Low To High" refers to the reflectivity changing from low to high during the burning process, which is the opposite of normal Blu-rays, whose reflectivity changes from high to low during writing. The advantage of BD-R LTH is it can protect a manufacturer's investment in DVD-R/CD-R manufacturing equipment because it does not require investing in new production lines and manufacturing equipment. Instead, the manufacturer only needs to modify current equipment. This is expected to lower the cost of disc manufacturing.[47]
Old Blu-ray players and recorders cannot utilize BD-R LTH; however, a firmware upgrade can enable devices to access BD-R LTH. Panasonic released such a firmware update in November 2007 for its DMR-BW200, DMR-BR100 and MR-BW900/BW800/BW700 models.[48] Pioneer was expected to ship the first LTH BD drives in Spring 2008.[49] Sony upgraded the PlayStation 3 firmware enabling BD-R LTH reading in March, 2008.[50]
In 2011, France's Ministry of Culture and Communication conducted a study on the suitability of data archival of LTH (low to high) discs compared to HTL (high to low) discs. The data they collected indicated that the overall quality of LTH discs is worse than HTL discs.[51][52]
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.
