Loading AI tools
Voltage booster electronic circuit From Wikipedia, the free encyclopedia
A joule thief is a minimalist self-oscillating voltage booster that is small, low-cost, and easy to build, typically used for driving small loads, such as driving an LED using a 1.5 volt battery. It can use nearly all of the energy in a single-cell electric battery, even far below the voltage where other circuits consider the battery fully discharged (or "dead"); hence the name, which suggests the notion that the circuit is "stealing" energy or "joules" from the source – the term is a pun on "jewel thief".
The circuit is a variant of the blocking oscillator that forms an unregulated voltage boost converter.
The joule thief is not a new concept. Basically, it adds an LED to the output of a self-oscillating voltage booster, which was patented many decades ago.
In November 1999 issue of Everyday Practical Electronics (EPE) magazine, the "Ingenuity Unlimited" (reader ideas) section had a novel circuit idea entitled "One Volt LED - A Bright Light" by Z. Kaparnik from Swindon, Wiltshire, UK. Three example circuits were shown for operating LEDs from supply voltages below 1.5 Volts. The basic circuits consisted of a transformer-feedback NPN transistor voltage converter based on the blocking oscillator. After testing three transistors (ZTX450 at 73% efficiency, ZTX650 at 79%, and BC550 at 57%), it was determined that a transistor with lower Vce(sat) yielded better efficiency results. Also, a resistor with lower resistance would yield a high current.[7]
 |
The circuit works by rapidly switching the transistor. Initially, current begins to flow through the resistor, secondary winding, and base-emitter junction (see diagram) which causes the transistor to begin conducting collector current through the primary winding. Since the two windings are connected in opposing directions, this induces a voltage in the secondary winding which is positive (due to the winding polarity, see dot convention) which turns the transistor on with higher bias. This self-stroking/positive-feedback process almost instantly turns the transistor on as hard as possible (putting it in the saturation region), making the collector-emitter path look like essentially a closed switch (since VCE will be only about 0.1 volts, assuming that the base current is high enough). With the primary winding effectively across the battery, the current increases at a rate proportional to the supply voltage divided by the inductance. Transistor switch-off takes place by different mechanisms dependent upon supply voltage. The gain of a transistor is not linear with VCE. At low supply voltages (typically 0.75 V and below) the transistor requires a larger base current to maintain saturation as the collector current increases. Hence, when it reaches a critical collector current, the base drive available becomes insufficient and the transistor starts to pinch off and the previously described positive feedback action occurs turning it hard off. To summarize, once the current in the coils stops increasing for any reason, the transistor goes into the cutoff region (and opens the collector-emitter "switch"). The magnetic field collapses, inducing however much voltage is necessary to make the load conduct, or for the secondary-winding current to find some other path. When the field is back to zero, the whole sequence repeats; with the battery ramping-up the primary-winding current until the transistor switches on. If the load on the circuit is very small the rate of rise and ultimate voltage at the collector is limited only by stray capacitances, and may rise to more than 100 times the supply voltage. For this reason, it is imperative that a load is always connected so that the transistor is not damaged. Because VCE is mirrored back to the secondary, failure of the transistor due to a small load will occur through the reverse VBE limit for the transistor being exceeded (this occurs at a much lower value than VCEmax). The transistor dissipates very little energy, even at high oscillating frequencies, because it spends most of its time in the fully on or fully off state, so either voltage over or current through the transistor is zero, thus minimizing the switching losses.
A simple modification of the previous schematic replaces the LED with three components to create a simple zener diode based voltage regulator. Diode D1 acts as a half-wave rectifier to allow capacitor C to charge up only when a higher voltage is available from the joule thief on the left side of diode D1. The Zener diode D2 limits the output voltage. As there is no regulation, any excess of energy not consumed by the load, will be dissipated as heat in the zener diode with consequent low efficiency of conversion.
When a more constant output voltage is desired, the joule thief can be given a closed-loop control. In the example circuit, the Schottky diode D1 blocks the charge built up on capacitor C1 from flowing back to the switching transistor Q1 when it is turned on. A 5.6 Volt Zener diode D2 and transistor Q2 forms the feedback control: when the voltage across the capacitor C1 is higher than the threshold voltage formed by Zener voltage of D2 plus the base-emitter turn-on voltage of transistor Q2, transistor Q2 is turned on diverting the base current of the switching transistor Q1, impeding the oscillation and prevents the voltage across capacitor C1 from rising even further. When the voltage across C1 drops below the threshold voltage Q2 turns off, allowing the oscillation to happen again. This very simple circuit has the drawback of temperature-dependent output voltage due to BJT2 (Vbe), and a relatively high ripple, but can be filtered with a simple LC pi network with low losses. In the example circuit, is included a low dropout regulator which contributes to regulating further the output voltage and lowers the ripple, but has the penalty of low conversion efficiency
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.
