Remove ads
A hard disk drive (HDD), hard disk or hard drive, is a data storage device for computers which uses magnetic storage to store data. The capacity of a hard drive is usually measured in gigabytes (GB), however hard disk capacity can also be measured in terabytes when the capacity is over 1000 or 1024 gigabytes. A gigabyte is one thousand megabytes and a megabyte is one million bytes, which means that a gigabyte is one billion bytes. Some hard drives are so large that their capacity is measured in terabytes, (TB) where one terabyte is a thousand gigabytes (1 TB = 1000 or 1024 GB). As of 2024, hard drives can go up to 32 TB in size.
Remove ads
Over the years there have been many disk interface types, though all used the same rotating platter recording technology. Differences were in how the data was encoded to binary, data integrity, data transfer speeds, cabling requirements, and cost. In 2009, it was common to attach a hard disk using a Serial ATA connection. The connection that came before that was called "IDE" and is called Parallel ATA today. In large data centers, Fibre Channel is often used.
For servers, the SCSI interface is very popular. There are several types and versions of SCSI interface, like parallel and Serial Attached SCSI, each stepping-up in terms of speed and price. Within servers, several SCSI drives are often used in conjunction with each other, in order to safeguard against data loss or corruption (this is known as RAID - and there are many configurations to choose from).
Remove ads
An HDD has a disk motor and an actuator motor that positions the read/write head. Wires from the actuator connect to the read/write head to amplifiers. They are bridged by the head support arm. In modern drives, acceleration at the head reaches 550 g, so a head support arm connects the actuator and the read/write head.
The actuator controls the read/write head and acts as a permanent magnet. A metal plate supports a squat neodymium-iron-boron (NIB) magnet. Beneath this plate is the voice coil, which is attached to the actuator hub. Beneath the actuator hub is a second NIB magnet, mounted on the bottom plate of the actuator.
The voice coil is shaped like an arrow. It is made up of a magnet with plastic insulation. This magnet interacts with the actuator magnet, causing the disk to move. If the magnetic field were uniform it would cancel out, but the surface magnet is divided between north and south poles in the middle so force is produced instead of canceled out.
Remove ads
There are several reasons behind the corruption of internal and external hard drive.[1]
Virus & Malware Attack:- If a system is attacked by a virus, the important boot files stored in the internal hard disk may be deleted, leading to boot failure. Meanwhile, the crucial data and the complete partition may also be deleted by the virus or malware attack.
Due to Physical Damage:- It is also called hardware failure, and consists the following types: Overheating of hard drive, Read/write head crash, Cracked or poor-contact data line, Scratch on magnetic platters, Short circuit in the control circuit board and much more. The data lost due to these kinds of reasons can hardly be repaired. A user have no choice but to turn to expert for data recovery from hardware damaged hard drive.
Corruption of Boot Sector:- The boot sector is the first sector of the hard drive. This is used to load processor control and then move it to the Operating System. When, the boot sector is damaged, you will not be able to enter the system and access any data stored in the internal hard drive.
Damaged file system:- The file system is used by the Operating System to define the approach for organizing files on the storage device. To be particular, it is like a gateway to access data stored on hard drive partitions. If the file system on the internal hard drive is unluckily damaged somehow, the drive may become inaccessible and the system may fail to start.
Software Clash:- All kinds of applications you installed on your local machine currently may not able to be fully supportive with each other, so software clash occurs now and then to lead to sudden computer shutdown and cause internal hard drive corruption.
Remove ads
When a hard disk fails to read the data, the hard drive may start to click to indicate that it is damaged, or broken. This can happen if you drop the hard disk, or the hard disk is just too old. The hard drive makes a "click" sound when that happens.
The clicking sound itself arises from the unexpected movement of the disk's read/write actuator. At start-up, and during use, the disk head must move correctly and confirm it is correctly tracking data on the disk. If the head cannot do this, the disk controller may attempt to recover by retrying. This may cause an audible "click". In some devices, the process automatically retries, causing a repeated or rhythmic clicking sound, sometimes accompanied by the whirring sound of the drive plate spinning. In this case when this happens, you might not be able to recover data on the hard disk without special data recovery services. However, there are reports that the hard drive may work again if you put it in the freezer overnight.
Remove ads
The platters in HDDs are spun at speeds varying from 4200 rpm in older portable devices designed for energy efficient operation, to 15000 rpm for high-performance servers(not for consumer use). The first HDDs spun at 1200 rpm and, for many years, 3600 rpm was the norm until the early 90s. However in terms of performance per Watt then 7200 rpm hard drives are the most energy efficient per gb of data transfered using not a substantial increase of energy than 5400rpm hdds. 4200rpm hdds are less efficient in terms of performance per Watt over 5400 rpm hdds which are better for larger file reads/writes due to it simply writing the files for a shorter time. 4200rpm is generally less effient than 5400rpm for most tasks. 5400rpm is better performing offering much better efficiency per Watt though 7200rpm drives only use slightly more power than 5400rpm making them slightly less efficient especially when idle.
As for higher rpms(10000/15000rpm) they are faster but use significantly more power than 7200rpm drive offering best balance of speed and power efficiency. Above 7200rpm efficiency of performance per Watt decreases especially with 15k rpm drives. So 7200rpm is most efficient followed by 5400 ,probably 4200 then 10000 and finally least efficient and mostly phased out 15000 rpm. 15k rpm doesn't offer much performance gains compared to 7200 and 10000 rpm. 4200rpm isn't produced anymore due to performance concerns while higher rpms are rare and only used in enterprise use but are mostly phased out because of falling ssd prices. 3600rpm is obsolete and last drives with this rpm were made in the early/mid 90s.10000rpm was a rare exception for WDs raptor drives which were 10k rpm sata drives marketed for both enterprise and consumer use. 15k rpm is only for enterprise hard drives. 4200rpm more common in older devices.
Remove ads
Wikiwand in your browser!
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.
Remove ads