Thermoelectric generator

A thermoelectric generator (TEG), also called a Seebeck generator, is a solid state device that converts heat (driven by temperature differences) directly into electrical energy through a phenomenon called the Seebeck effect^[1] (a form of thermoelectric effect). Thermoelectric generators function like heat engines, but are less bulky and have no moving parts. However, TEGs are typically more expensive and less efficient.^[2] When the same principle is used in reverse to create a heat gradient from an electric current, it is called a thermoelectric (or Peltier) cooler.

Thermoelectric generators could be used in power plants and factories to convert waste heat into additional electrical power and in automobiles as automotive thermoelectric generators (ATGs) to increase fuel efficiency. Radioisotope thermoelectric generators use radioisotopes to generate the required temperature difference to power space probes.^[2] Thermoelectric generators can also be used alongside solar panels.^[3][4]

History

In 1821, Thomas Johann Seebeck discovered that a thermal gradient formed between two different conductors can produce electricity.^[5][6] At the heart of the thermoelectric effect is that a temperature gradient in a conducting material results in heat flow; this results in the diffusion of charge carriers. The flow of charge carriers between the hot and cold regions in turn creates a voltage difference. In 1834, Jean Charles Athanase Peltier discovered the reverse effect, that running an electric current through the junction of two dissimilar conductors could, depending on the direction of the current, cause it to act as a heater or cooler.^[7]

George Cove's solar panel pictured in The Technical World Magazine in March 1909.^[8]

George Cove had accidentally invented a photovoltaic panel, despite intending to invent a thermoelectric generator with thermocouples, in 1909.^[9] He notes that heat alone didn't produce any power, only incident light, but he had no explanation for how it could be working. The operational principle is now understood to have been a very simple form of Schottky junction.

Efficiency

The typical efficiency of TEGs is around 5–8%, although it can be higher. Older devices used bimetallic junctions and were bulky. More recent devices use highly doped semiconductors made from bismuth telluride (Bi₂Te₃), lead telluride (PbTe),^[10] calcium manganese oxide (Ca₂Mn₃O₈),^[11][12] or combinations thereof,^[13] depending on application temperature. These are solid-state devices and unlike dynamos have no moving parts, with the occasional exception of a fan or pump to improve heat transfer. If the hot region is around 1273K and the ZT values of 3 - 4 are implemented, the efficiency is approximately 33-37%; allowing TEG's to compete with certain heat engine efficiencies.^[14]

As of 2021, there are materials (some containing widely available and inexpensive arsenic and tin) reaching a ZT value > 3; monolayer ${\displaystyle {\ce {AsP3}}}$ (ZT = 3.36 on the armchair axis); n-type doped ${\displaystyle {\ce {InP3}}}$ (ZT = 3.23); p-type doped ${\displaystyle {\ce {SnP3}}}$ (ZT = 3.46); p-type doped ${\displaystyle {\ce {SbP3}}}$ (ZT = 3.5).^[15]

Construction

Seebeck effect in a thermopile made from iron and copper wires

Thermoelectric power generators consist of three major components: thermoelectric materials, thermoelectric modules and thermoelectric systems that interface with the heat source.^[16]

Thermoelectric materials

Main article: Thermoelectric materials

Thermoelectric materials generate power directly from the heat by converting temperature differences into electric voltage. These materials must have both high electrical conductivity (σ) and low thermal conductivity (κ) to be good thermoelectric materials. Having low thermal conductivity ensures that when one side is made hot, the other side stays cold, which helps to generate a large voltage while in a temperature gradient. The measure of the magnitude of electrons flow in response to a temperature difference across that material is given by the Seebeck coefficient (S). The efficiency of a given material to produce a thermoelectric power is simply estimated by its “figure of merit” zT = S²σT/κ.

For many years, the main three semiconductors known to have both low thermal conductivity and high power factor were bismuth telluride (Bi₂Te₃), lead telluride (PbTe), and silicon germanium (SiGe). Some of these materials have somewhat rare elements which make them expensive.^{[citation needed]}

Today, the thermal conductivity of semiconductors can be lowered without affecting their high electrical properties using nanotechnology. This can be achieved by creating nanoscale features such as particles, wires or interfaces in bulk semiconductor materials. However, the manufacturing processes of nano-materials are still challenging.

A thermoelectric circuit composed of materials of different Seebeck coefficient (p-doped and n-doped semiconductors), configured as a thermoelectric generator.

Thermoelectric advantages

Thermoelectric generators are all-solid-state devices that do not require any fluids for fuel or cooling, making them non-orientation dependent allowing for use in zero-gravity or deep-sea applications.^[17] The solid-state design allows for operation in severe environments. Thermoelectric generators have no moving parts which produce a more reliable device that does not require maintenance for long periods. The durability and environmental stability have made thermoelectrics a favorite for NASA's deep space explorers among other applications.^[18] One of the key advantages of thermoelectric generators outside of such specialized applications is that they can potentially be integrated into existing technologies to boost efficiency and reduce environmental impact by producing usable power from waste heat.^[19]

Thermoelectric module

A thermoelectric module is a circuit containing thermoelectric materials which generate electricity from heat directly. A thermoelectric module consists of two dissimilar thermoelectric materials joined at their ends: an n-type (with negative charge carriers), and a p-type (with positive charge carriers) semiconductor. Direct electric current will flow in the circuit when there is a temperature difference between the ends of the materials. Generally, the current magnitude is directly proportional to the temperature difference:

${\displaystyle \mathbf {J} =-\sigma S\nabla T}$

where ${\displaystyle \sigma }$ is the local conductivity, S is the Seebeck coefficient (also known as thermopower), a property of the local material, and ${\displaystyle \nabla T}$ is the temperature gradient.

In application, thermoelectric modules in power generation work in very tough mechanical and thermal conditions. Because they operate in a very high-temperature gradient, the modules are subject to large thermally induced stresses and strains for long periods. They also are subject to mechanical fatigue caused by a large number of thermal cycles.

Thus, the junctions and materials must be selected so that they survive these tough mechanical and thermal conditions. Also, the module must be designed such that the two thermoelectric materials are thermally in parallel, but electrically in series. The efficiency of a thermoelectric module is greatly affected by the geometry of its design.

Thermoelectric design

Thermoelectric generators are made of several thermopiles, each consisting of many thermocouples made of a connected n-type and p-type material. The arrangement of the thermocouples is typically in three main designs: planar, vertical, and mixed. Planar design involves thermocouples put onto a substrate horizontally between the heat source and cool side, resulting in the ability to create longer and thinner thermocouples, thereby increasing the thermal resistance and temperature gradient and eventually increasing voltage output. Vertical design has thermocouples arranged vertically between the hot and cool plates, leading to high integration of thermocouples as well as a high output voltage, making this design the most widely-used design commercially. The mixed design has the thermocouples arranged laterally on the substrate while the heat flow is vertical between plates. Microcavities under the hot contacts of the device allow for a temperature gradient, which allows for the substrate’s thermal conductivity to affect the gradient and efficiency of the device.^[20]

For microelectromechanical systems, TEGs can be designed on the scale of handheld devices to use body heat in the form of thin films.^[21] Flexible TEGs for wearable electronics are able to be made with novel polymers through additive manufacturing or thermal spraying processes. Cylindrical TEGs for using heat from vehicle exhaust pipes can also be made using circular thermocouples arranged in a cylinder.^[22] Many designs for TEGs can be made for the different devices they are applied to.

Thermoelectric systems

Using thermoelectric modules, a thermoelectric system generates power by taking in heat from a source such as a hot exhaust flue. To operate, the system needs a large temperature gradient, which is not easy in real-world applications. The cold side must be cooled by air or water. Heat exchangers are used on both sides of the modules to supply this heating and cooling.

There are many challenges in designing a reliable TEG system that operates at high temperatures. Achieving high efficiency in the system requires extensive engineering design to balance between the heat flow through the modules and maximizing the temperature gradient across them. To do this, designing heat exchanger technologies in the system is one of the most important aspects of TEG engineering. In addition, the system requires to minimize the thermal losses due to the interfaces between materials at several places. Another challenging constraint is avoiding large pressure drops between the heating and cooling sources.

If AC power is required (such as for powering equipment designed to run from AC mains power), the DC power from the TE modules must be passed through an inverter, which lowers efficiency and adds to the cost and complexity of the system.

Materials for TEG

Only a few known materials to date are identified as thermoelectric materials. Most thermoelectric materials today have a zT, the figure of merit, value of around 1, such as in bismuth telluride (Bi₂Te₃) at room temperature and lead telluride (PbTe) at 500–700 K. However, in order to be competitive with other power generation systems, TEG materials should have a zT of 2–3. Most research in thermoelectric materials has focused on increasing the Seebeck coefficient (S) and reducing the thermal conductivity, especially by manipulating the nanostructure of the thermoelectric materials. Because both the thermal and electrical conductivity correlate with the charge carriers, new means must be introduced in order to conciliate the contradiction between high electrical conductivity and low thermal conductivity, as is needed.^[23]

When selecting materials for thermoelectric generation, a number of other factors need to be considered. During operation, ideally, the thermoelectric generator has a large temperature gradient across it. Thermal expansion will then introduce stress in the device which may cause fracture of the thermoelectric legs or separation from the coupling material. The mechanical properties of the materials must be considered and the coefficient of thermal expansion of the n and p-type material must be matched reasonably well. In segmented^[24] thermoelectric generators, the material's compatibility must also be considered to avoid incompatibility of relative current, defined as the ratio of electrical current to diffusion heat current, between segment layers.

A material's compatibility factor is defined as

${\displaystyle s={\frac {{\sqrt {1+zT}}-1}{ST}}}$.^[25]

When the compatibility factor from one segment to the next differs by more than a factor of about two, the device will not operate efficiently. The material parameters determining s (as well as zT) are temperature-dependent, so the compatibility factor may change from the hot side to the cold side of the device, even in one segment. This behavior is referred to as self-compatibility and may become important in devices designed for wide-temperature application.

In general, thermoelectric materials can be categorized into conventional and new materials:

Conventional materials

Many TEG materials are employed in commercial applications today. These materials can be divided into three groups based on the temperature range of operation:

1. Low temperature materials (up to around 450 K): Alloys based on bismuth (Bi) in combinations with antimony (Sb), tellurium (Te) or selenium (Se).
2. Intermediate temperature (up to 850 K): such as materials based on alloys of lead (Pb)
3. Highest temperatures material (up to 1300 K): materials fabricated from silicon-germanium (SiGe) alloys.^[26]

Although these materials still remain the cornerstone for commercial and practical applications in thermoelectric power generation, significant advances have been made in synthesizing new materials and fabricating material structures with improved thermoelectric performance. Recent research has focused on improving the material’s figure-of-merit (zT), and hence the conversion efficiency, by reducing the lattice thermal conductivity.^[23]

New materials

Generation of electricity by grabbing both sides of a flexible PEDOT:PSS thermoelectric device

PEDOT:PSS-based model embedded into a glove to generate electricity by body heat

Researchers are trying to develop new thermoelectric materials for power generation by improving the figure-of-merit zT. One example of these materials is the semiconductor compound ß-Zn₄Sb₃, which possesses an exceptionally low thermal conductivity and exhibits a maximum zT of 1.3 at a temperature of 670K. This material is also relatively inexpensive and stable up to this temperature in a vacuum, and can be a good alternative in the temperature range between materials based on Bi₂Te₃ and PbTe.^[23] Among the most exciting developments in thermoelectric materials was the development of single crystal tin selenide which produced a record zT of 2.6 in one direction.^[27] Other new materials of interest include Skutterudites, Tetrahedrites, and rattling ions crystals.^{[citation needed]}

Besides improving the figure-of-merit, there is increasing focus to develop new materials by increasing the electrical power output, decreasing cost and developing environmentally friendly materials. For example, when the fuel cost is low or almost free, such as in waste heat recovery, then the cost per watt is only determined by the power per unit area and the operating period. As a result, it has initiated a search for materials with high power output rather than conversion efficiency. For example, the rare earth compounds YbAl₃ has a low figure-of-merit, but it has a power output of at least double that of any other material, and can operate over the temperature range of a waste heat source.^[23]

Novel processing

To increase the figure of merit (zT), a material’s thermal conductivity should be minimized while its electrical conductivity and Seebeck coefficient is maximized. In most cases, methods to increase or decrease one property result in the same effect on other properties due to their interdependence. A novel processing technique exploits the scattering of different phonon frequencies to selectively reduce lattice thermal conductivity without the typical negative effects on electrical conductivity from the simultaneous increased scattering of electrons.^[28] In a bismuth antimony tellurium ternary system, liquid-phase sintering is used to produce low-energy semicoherent grain boundaries, which do not have a significant scattering effect on electrons.^[29] The breakthrough is then applying a pressure to the liquid in the sintering process, which creates a transient flow of the Te rich liquid and facilitates the formation of dislocations that greatly reduce the lattice conductivity.^[29] The ability to selectively decrease the lattice conductivity results in reported zT value of 1.86, which is a significant improvement over the current commercial thermoelectric generators with zT ~ 0.3–0.6.^[30] These improvements highlight the fact that in addition to the development of novel materials for thermoelectric applications, using different processing techniques to design microstructure is a viable and worthwhile effort. In fact, it often makes sense to work to optimize both composition and microstructure.^[31]

Uses

Thermoelectric generators (TEG) have a variety of applications. Frequently, thermoelectric generators are used for low power remote applications or where bulkier but more efficient heat engines such as Stirling engines would not be possible. Unlike heat engines, the solid state electrical components typically used to perform thermal to electric energy conversion have no moving parts. The thermal to electric energy conversion can be performed using components that require no maintenance, have inherently high reliability, and can be used to construct generators with long service-free lifetimes. This makes thermoelectric generators well suited for equipment with low to modest power needs in remote uninhabited or inaccessible locations such as mountaintops, the vacuum of space, or the deep ocean.

The main uses of thermoelectric generators are:

• Space probes, including the Mars Curiosity rover, generate electricity using a radioisotope thermoelectric generator whose heat source is a radioactive element.
• Waste heat recovery. Every human activity, transport and industrial process generates waste heat, being possible to harvest residual energy from cars, aircraft, ships, industries and the human body.^[1] From cars the main source of energy is the exhaust gas.^[32] Harvesting that heat energy using a thermoelectric generator can increase the fuel efficiency of the car. Thermoelectric generators have been investigated to replace the alternators in cars demonstrating a 3.45% reduction in fuel consumption.^[33] Projections for future improvements are up to a 10% increase in mileage for hybrid vehicles.^[34] It has been stated that the potential energy savings could be higher for gasoline engines rather than for diesel engines.^[35] For more details, see the article: Automotive thermoelectric generator. For aircraft, engine nozzles have been identified as the best place to recover energy from, but heat from engine bearings and the temperature gradient existing in the aircraft skin have also been proposed.^[1]
• Solar cells use only the high-frequency part of the radiation, while the low-frequency heat energy is wasted. Several patents about the use of thermoelectric devices in parallel or cascade configuration with solar cells have been filed.^[1][36] The idea is to increase the efficiency of the combined solar/thermoelectric system to convert solar radiation into useful electricity.
• Thermoelectric generators are primarily used as remote and off-grid power generators for unmanned sites. They are the most reliable power generator in such situations as they do not have moving parts (thus virtually maintenance-free), work day and night, perform under all weather conditions and can work without battery backup. Although solar photovoltaic systems are also implemented in remote sites, Solar PV may not be a suitable solution where solar radiation is low, i.e. areas at higher latitudes with snow or no sunshine, areas with much cloud or tree canopy cover, dusty deserts, forests, etc. Thermoelectric generators are commonly used on gas pipelines, for example, for cathodic protection, radio communication, and telemetry. On gas pipelines for power consumption of up to 5 kW, thermal generators are preferable to other power sources. The manufacturers of generators for gas pipelines are Global Power Technologies (formerly Global Thermoelectric) (Calgary, Canada) and TELGEN (Russia).
• Microprocessors generate waste heat. Researchers have considered whether some of that energy could be recycled.^[37] (However, see below for problems that can arise.)
• Thermoelectric generators have also been investigated as standalone solar-thermal cells. Integration of thermoelectric generators have been directly integrated to a solar thermal cell with efficiency of 4.6%.^[38]
• The Maritime Applied Physics Corporation in Baltimore, Maryland is developing a thermoelectric generator to produce electric power on the deep-ocean offshore seabed using the temperature difference between cold seawater and hot fluids released by hydrothermal vents, hot seeps, or from drilled geothermal wells. A high-reliability source of seafloor electric power is needed for ocean observatories and sensors used in the geological, environmental, and ocean sciences, by seafloor mineral and energy resource developers, and by the military. Recent studies have found that deep-sea thermoelectric generators for large scale energy plants are also economically viable.^[39]
• Ann Makosinski from British Columbia, Canada has developed several devices using Peltier tiles to harvest heat (from a human hand,^[40] the forehead, and hot beverage^[41]) that claims to generate enough electricity to power an LED light or charge a mobile device, although the inventor admits that the brightness of the LED light is not competitive with those on the market.^[42]
• Thermoelectric generators are used in stove fans. They are put on top of a wood or coal burning stove. The TEG is sandwiched between 2 heat sinks and the difference in temperature will power a slow-moving fan that helps circulate the stove's heat into the room.^[43]

Practical limitations

Besides low efficiency and relatively high cost, practical problems exist in using thermoelectric devices in certain types of applications resulting from a relatively high electrical output resistance, which increases self-heating, and a relatively low thermal conductivity, which makes them unsuitable for applications where heat removal is critical, as with heat removal from an electrical device such as microprocessors.

• High generator output resistance: To get voltage output levels in the range required by digital electrical devices, a common approach is to place many thermoelectric elements in series within a generator module. The element's voltages increase, but so does their output resistance. The maximum power transfer theorem dictates that maximum power is delivered to a load when the source and load resistances are identically matched. For low impedance loads near zero ohms, as the generator resistance rises the power delivered to the load decreases. To lower the output resistance, some commercial devices place more individual elements in parallel and fewer in series and employ a boost regulator to raise the voltage to the voltage needed by the load.
• Low thermal conductivity: Because a very high thermal conductivity is required to transport thermal energy away from a heat source such as a digital microprocessor, the low thermal conductivity of thermoelectric generators makes them unsuitable to recover the heat.
• Cold-side heat removal with air: In air-cooled thermoelectric applications, such as when harvesting thermal energy from a motor vehicle's crankcase, the large amount of thermal energy that must be dissipated into ambient air presents a significant challenge. As a thermoelectric generator's cool side temperature rises, the device's differential working temperature decreases. As the temperature rises, the device's electrical resistance increases causing greater parasitic generator self-heating. In motor vehicle applications a supplementary radiator is sometimes used for improved heat removal, though the use of an electric water pump to circulate a coolant adds parasitic loss to total generator output power. Water cooling the thermoelectric generator's cold side, as when generating thermoelectric power from the hot crankcase of an inboard boat motor, would not suffer from this disadvantage. Water is a far easier coolant to use effectively in contrast to air.

Future[when?] market

While TEG technology has been used in military and aerospace applications for decades, new TE materials^[44] and systems are being developed to generate power using low or high temperatures waste heat, and that could provide a significant opportunity in the near future. These systems can also be scalable to any size and have lower operation and maintenance cost.

The global market for thermoelectric generators is estimated to be US$320 million in 2015 and US$472 million in 2021; up to US$1.44 billion by 2030 with a CAGR of 11.8%.^[45] Today, North America captures 66% of the market share and it will continue to be the biggest market in the near future.^[46] However, Asia-Pacific and European countries are projected to grow at relatively higher rates. A study found that the Asia-Pacific market would grow at a Compound Annual Growth Rate (CAGR) of 18.3% in the period from 2015 to 2020 due to the high demand of thermoelectric generators by the automotive industries to increase overall fuel efficiency, as well as the growing industrialization in the region.^[47]

Small scale thermoelectric generators are also in the early stages of investigation in wearable technologies to reduce or replace charging and boost charge duration. Recent studies focused on the novel development of a flexible inorganic thermoelectric, silver selenide, on a nylon substrate. Thermoelectrics represent particular synergy with wearables by harvesting energy directly from the human body creating a self-powered device. One project used n-type silver selenide on a nylon membrane. Silver selenide is a narrow bandgap semiconductor with high electrical conductivity and low thermal conductivity, making it perfect for thermoelectric applications.^[48]

Low power TEG or "sub-watt" (i.e. generating up to 1 watt peak) market is a growing part of the TEG market, capitalizing on the latest technologies. Main applications are sensors, low power applications and more globally Internet of things applications. A specialized market research company indicated that 100,000 units have been shipped in 2014 and expects 9 million units per year by 2020.^[49]

See also

• Bismuth telluride
• Electrical generator
• Energy harvesting devices: Thermoelectrics
• Gentherm Incorporated
• Mária Telkes
• Stirling engine
• Thermal power station
• Thermoelectric battery
• Thermionic converter
• Thermoelectric cooling or Peltier cooler
• Thermoelectric effect
• Thermoelectric materials

References

1. Fernández-Yáñez, P.; Romero, V.; Armas, O.; Cerretti, G. (September 2021). "Thermal management of thermoelectric generators for waste energy recovery". Applied Thermal Engineering. 196: 117291. Bibcode:2021AppTE.19617291F. doi:10.1016/j.applthermaleng.2021.117291.
2. Adroja, Nikunj; Mehta, Shruti B.; Shah, Pratik (2015-03-01). "Review of thermoelectricity to improve energy quality". Journal of Emerging Technologies and Innovative Research. 2 (3 (March-2015)). Jetir.
3. "New solar panels generate electricity long after the sun sets". 11 April 2022.
4. Kraemer, Daniel; Poudel, Bed; Feng, Hsien-Ping; Caylor, J. Christopher; Yu, Bo; Yan, Xiao; Ma, Yi; Wang, Xiaowei; Wang, Dezhi; Muto, Andrew; McEnaney, Kenneth; Chiesa, Matteo; Ren, Zhifeng; Chen, Gang (July 2011). "High-performance flat-panel solar thermoelectric generators with high thermal concentration". Nature Materials. 10 (7): 532–538. Bibcode:2011NatMa..10..532K. doi:10.1038/nmat3013. PMID 21532584.
5. Seebeck, T. J. (1825). "Magnetische Polarisation der Metalle und Erze durch Temperatur-Differenz (Magnetic polarization of metals and minerals by temperature differences)". Abhandlungen der Königlichen Akademie der Wissenschaften zu Berlin (Treatises of the Royal Academy of Sciences in Berlin). pp. 265–373.
6. Seebeck, T. J. (1826). "Ueber die Magnetische Polarisation der Metalle und Erze durch Temperatur-Differenz," (On the magnetic polarization of metals and minerals by temperature differences)". Annalen der Physik und Chemie. 6: 286.
7. Peltier (1834). "Nouvelles expériences sur la caloricité des courants électrique (New experiments on the heat effects of electric currents)". Annales de Chimie et de Physique. 56: 371–386.
8. "The Latest Type of Solar Electric Generator". The Technical World Magazine. March 1909. p. 358.
9. "How to Build a Low-tech Solar Panel?". Low-Tech Magazine. 5 October 2021. Retrieved 2024-09-02.
10. Biswas, Kanishka; He, Jiaqing; Blum, Ivan D.; Wu, Chun-I; Hogan, Timothy P.; Seidman, David N.; Dravid, Vinayak P.; Kanatzidis, Mercouri G. (2012). "High-performance bulk thermoelectrics with all-scale hierarchical architectures". Nature. 489 (7416): 414–418. Bibcode:2012Natur.489..414B. doi:10.1038/nature11439. PMID 22996556. S2CID 4394616.
11. Ansell, G. B.; Modrick, M. A.; Longo, J. M.; Poeppeimeler, K. R.; Horowitz, H. S. (1982). "Calcium manganese oxide Ca₂Mn₃O₈" (PDF). Acta Crystallographica Section B. 38 (6). International Union of Crystallography: 1795–1797. doi:10.1107/S0567740882007201.
12. "EspressoMilkCooler.com – TEG CMO 800°C & Cascade 600°C Hot Side Thermoelectric Power Modules". espressomilkcooler.com.
13. "High Temp Teg Power Modules". Archived from the original on December 17, 2012.
14. "Thermoelectric Generators". large.stanford.edu. Retrieved 2022-10-27.
15. Fan, Liangshuang; Yang, Hengyu; Xie, Guofeng (2021). "Thermoelectric Properties of Arsenic Triphosphide (AsP3) Monolayer: A First-Principles Study". Frontiers in Mechanical Engineering. 7. doi:10.3389/fmech.2021.702079.
16. "How Thermoelectric Generators Work – Alphabet Energy". Alphabet Energy. Retrieved 2015-10-28.
17. Chen, Meng (2015-04-29). "The Deep Sea Water and Heat Energy of Thermoelectric Generation Study". ECS Meeting Abstracts. MA2015-01 (3). The Electrochemical Society: 706. doi:10.1149/MA2015-01/3/706. Retrieved 11 March 2019.
18. "Advanced Thermoelectric Technology: Powering Spacecraft and Instruments to Explore the Solar System". NASA. Retrieved 11 March 2019.
19. Walker, Kris (2013-01-28). "How Can Thermo Electrical Generators Help the Environment?". AZO Clean Tech. Retrieved 11 March 2019.
20. Jaziri, Nesrine; Boughamoura, Ayda; Müller, Jens; Mezghani, Brahim; Tounsi, Fares; Ismail, Mohammed (2020-12-01). "A comprehensive review of Thermoelectric Generators: Technologies and common applications". Energy Reports. SI:Energy Storage - driving towards a clean energy future. 6: 264–287. Bibcode:2020EnRep...6..264J. doi:10.1016/j.egyr.2019.12.011. S2CID 212902804.
21. Addanki, Satish; Nedumaran, D. (December 2019). "Simulation and fabrication of thermoelectric generators for hand held electronic gadgets". Materials Science and Engineering: B. 251: 114453. doi:10.1016/j.mseb.2019.114453. S2CID 209724788.
22. Kumar, Palanisamy Mohan; Jagadeesh Babu, Veluru; Subramanian, Arjun; Bandla, Aishwarya; Thakor, Nitish; Ramakrishna, Seeram; Wei, He (June 2019). "The Design of a Thermoelectric Generator and Its Medical Applications". Designs. 3 (2): 22. doi:10.3390/designs3020022.
23. Ismail, Basel I.; Ahmed, Wael H. (2009-01-01). "Thermoelectric Power Generation Using Waste-Heat Energy as an Alternative Green Technology". Recent Patents on Electrical & Electronic Engineering. 2 (1): 27–39. doi:10.2174/1874476110902010027.
24. Goldsmid, H. Julian (2016). Introduction to Thermoelectricity. Springer Series in Materials Science. Vol. 121. Berlin, Heidelberg: Springer Berlin Heidelberg. Bibcode:2016inh..book.....G. doi:10.1007/978-3-662-49256-7. ISBN 978-3-662-49255-0.
25. Snyder, G. (Oct 2003). "Thermoelectric Efficiency and Compatibility" (PDF). Physical Review Letters. 91 (14): 148301. Bibcode:2003PhRvL..91n8301S. doi:10.1103/physrevlett.91.148301. PMID 14611561.
26. Kandemir, Ali; Ozden, Ayberk; Cagin, Tahir; Sevik, Cem (2017). "Thermal conductivity engineering of bulk and one-dimensional Si-Ge nanoarchitectures". Science and Technology of Advanced Materials. 18 (1): 187–196. Bibcode:2017STAdM..18..187K. doi:10.1080/14686996.2017.1288065. PMC 5404179. PMID 28469733.
27. Kanatzidis, M (2014). "Ultralow thermal conductivity and high thermoelectric figure of merit in Sn Se crystals". Nature. 508 (7496): 373–377. Bibcode:2014Natur.508..373Z. doi:10.1038/nature13184. PMID 24740068. S2CID 205238132.
28. Hori, Takuma; Shiomi, Junichiro (2018). "Tuning phonon transport spectrum for better thermoelectric materials". Science and Technology of Advanced Materials. 20 (1): 10–25. doi:10.1080/14686996.2018.1548884. PMC 6454406. PMID 31001366.
29. Kim, Sang (2015). "Dense dislocation arrays embedded in grain boundaries for high-performance bulk thermoelectrics" (PDF). Science. 348 (6230): 109–114. Bibcode:2015Sci...348..109K. doi:10.1126/science.aaa4166. PMID 25838382. S2CID 31412977.
30. Kim, D.S. (2008). "Solar refrigeration options – a state-of-the-art review". International Journal of Refrigeration. 31 (1): 3–15. doi:10.1016/j.ijrefrig.2007.07.011.
31. Cojocaru-Mirédin, Oana. "Thermoelectric Materials Design by controlling the microstructure and composition". Max-Planck Institut. Retrieved 8 November 2016.
32. Ezzitouni, S.; Fernández-Yáñez, P.; Sánchez, L.; Armas, O. (July 2020). "Global energy balance in a diesel engine with a thermoelectric generator". Applied Energy. 269: 115139. Bibcode:2020ApEn..26915139E. doi:10.1016/j.apenergy.2020.115139. S2CID 219428113.
33. John, Fairbanks (2014). "Automotive Thermoelectric Generators and HVAC" (PDF). Department of Energy. Retrieved 11 March 2019.
34. Fehrenbacher, Katie. "A startup is finally bringing heat-to-power tech in a big way for vehicles". Fortune. Retrieved 11 March 2019.
35. Fernández-Yáñez, P.; Armas, O.; Kiwan, R.; Stefanopoulou, A.; Boehman, A.L. (2018). "A thermoelectric generator in exhaust systems of spark-ignition and compression-ignition engines. A comparison with an electric turbo-generator". Applied Energy. 229: 80–87. Bibcode:2018ApEn..229...80F. doi:10.1016/j.apenergy.2018.07.107. S2CID 116417579.
36. Kraemer, D; Hu, L; Muto, A; Chen, X; Chen, G; Chiesa, M (2008), "Photovoltaic-thermoelectric hybrid systems: A general optimization methodology", Applied Physics Letters, 92 (24): 243503, Bibcode:2008ApPhL..92x3503K, doi:10.1063/1.2947591, S2CID 109824202
37. Zhou, Yu; Paul, Somnath; Bhunia, Swarup (2008). "Harvesting Wasted Heat in a Microprocessor Using Thermoelectric Generators: Modeling, Analysis and Measurement". 2008 Design, Automation and Test in Europe. pp. 98–103. doi:10.1109/DATE.2008.4484669. ISBN 978-3-9810801-3-1.
38. Kraemer, Daniel (2011). "High-performance flat-panel solar thermoelectric generators with high thermal concentration". Nature Materials. 10 (7): 532–538. Bibcode:2011NatMa..10..532K. doi:10.1038/nmat3013. PMID 21532584.
39. Liu, Lipeng (2014). "Feasibility of large-scale power plants based on thermoelectric effects". New Journal of Physics. 16 (12): 123019. Bibcode:2014NJPh...16l3019L. doi:10.1088/1367-2630/16/12/123019.
40. "GSF 2013 : Project : The Hollow Flashlight". Google Science Fair. Retrieved 2015-12-25.
41. Makosinski, Ann. "The e-Drink: Capturing Electricity from Beverages".
42. Chung, Emily (June 17, 2014). "B.C. Girl invents headlamp powered by body heat". CBC News.
43. "Army Logistician". 1998.
44. Pöhls, Jan-Hendrik (16 December 2021). "A new approach finds materials that can turn waste heat into electricity". The Conversation. Retrieved 2022-01-05.
45. "Thermoelectric Generator Market Analysis - 2030 | By Material, Application". Allied Market Research. Retrieved 2022-11-11.
46. "Global Thermoelectric Generator Market is estimated to cross the US $720 million by 2021: by Market Research Engine". www.keyc.com. Retrieved 2015-10-28.
47. "Thermoelectric Generators Market Worth 547.7 Million USD by 2020". www.prnewswire.com (Press release). Retrieved 2015-10-28.
48. Ding, Y. (2019). "High performance n-type Ag₂Se film on nylon membrane for flexible thermoelectric power generator". Nature Communications. 10 (841): 841. doi:10.1038/s41467-019-08835-5. PMC 6381183. PMID 30783113.
49. "Sub-watt thermoelectric generator market on the up". 2016-03-15. Retrieved 2016-09-13.

External links

• Callendar, Hugh Longbourne (1911). "Thermoelectricity" . Encyclopædia Britannica. Vol. 26 (11th ed.). pp. 814–821.
• Small Thermoelectric Generators by G. Jeffrey Snyder
• Kanellos, M. (2008, November 24). Tapping America’s Secret Power Source. Retrieved from Greentech Media, October 30, 2009. Web site: Tapping America's Secret Power Source
• LT Journal October 2010: Ultralow Voltage Energy Harvester Uses Thermoelectric Generator for Battery-Free Wireless Sensors
• DIY: How to Build a Thermoelectric Energy Generator With a Cheap Peltier Unit
• Gentherm Inc.
• This device harnesses the cold night sky to generate electricity in the dark