Loading AI tools
US Navy carrier-based fighter-bomber aircraft in service 1951–1959 From Wikipedia, the free encyclopedia
The Vought F7U Cutlass is a United States Navy carrier-based jet fighter and fighter-bomber designed and produced by the aircraft manufacturer Chance Vought. It was the first tailless production fighter in the United States as well as the Navy's first jet equipped with swept wings and the first to be designed with afterburners.[1]
| F7U Cutlass | |
|---|---|
| A US Navy F7U Cutlass circa 1955 | |
| General information | |
| Type | Naval multirole fighter |
| National origin | United States |
| Manufacturer | Chance Vought |
| Primary user | United States Navy |
| Number built | 320 |
| History | |
| Manufactured | 1948–1955 |
| Introduction date | July 1951 |
| First flight | 29 September 1948 |
| Retired | 2 March 1959 |
The Cutlass was developed from the mid 1940s to early 1950s as Vought's entry in a United States Navy competition. Their design team, which was influenced by design information obtained from Nazi Germany, opted for a tailless configuration paired with low aspect ratio swept wings, which was regarded as a radical departure from traditional aircraft design for the era. Vought's submission was favoured by Navy officials and was declared the winner in 1946. On 29 September 1948, the prototype performed its maiden flight; all three prototypes would be lost during the flight test program. It was initially powered by a pair of Westinghouse J34 turbojet engines which were relatively underpowered, contributing to its accident-prone nature; its unreliable hydraulic flight control system was also a source of difficulties.
The first production model of the Cutlass, F7U-1, entered service during July 1951. It was promptly followed by F7U-2 and F7U-3, improved models that were equipped with more powerful engines amongst other refinements. However, the Cutlass continued to suffer from frequent technical and handling problems throughout the aircraft's short service career. Accidents involving the type were responsible for the deaths of four test pilots and 21 other U.S. Navy pilots.[2] Over one quarter of all Cutlasses built were destroyed in accidents; this high rate of accidents led to the type being withdrawn during the late 1950s despite having been in service for less than ten years.[3]
The Cutlass was developed in response to a competition organised by the United States Navy for a new carrier-capable day fighter that was launched on 1 June 1945.[4] Specific requirements of the competition included the ability to fly at speeds of up to 600 miles per hour (970 km/h) and altitudes of up to 40,000 feet (12,000 m).[2][1] Vought decided to respond with a relatively radical design for the era.[4]
Vought's design team opted for an unconventional tailless configuration; this decision was heavily influenced by aerodynamic data obtained for various wartime projects undertaken by the German Arado and Messerschmitt companies that had been obtained at the close of World War II through German scientists who worked on the projects, though Vought designers denied any link to the German research at the time.[2] Specifically, former Messerschmitt AG senior designer Woldemar Voigt, who supervised the development of numerous experimental jet fighters in Nazi Germany, contributed to its design with his experience in the development of the Messerschmitt P.1110 and P.1112 projects.[5][6] The F7U was the last aircraft designed by Rex Beisel, who was responsible for the first fighter ever designed specifically for the U.S. Navy, the Curtiss TS-1 of 1922.
Vought's design was given the company type number V-346 and later received the official designation of F7U when the aircraft was announced to be the winner of the competition.[2] Reviewing official found the design, despite its unconventional nature, to pose an acceptable level of risk, less so than some of the competing submissions. During June 1946, an initial order for three XF7U-1 prototypes, each powered by a pair of Westinghouse J34 turbojet engines, was issued to the company.[4] Construction took place at Vought's plant in Stratford, Connecticut.[7]
On 29 September 1948, the first prototype performed its maiden flight from Naval Air Station Patuxent River in Maryland, piloted by Vought's chief test pilot, J. Robert Baker.[8][9] Several issues were encountered during this initial flight. Shortly thereafter, the Navy announced that the aircraft would be named Cutlass.[10] During subsequent flight testing, one of the prototypes attained a maximum speed of 625 mph (1,058 km/h).[11]
During September 1949, Vought received a contract to modify the design and to produce 88 F7U-2 Cutlasses for the Navy.[10] In May 1950, the Navy opted to halt F7U-1 production at 14 aircraft in favor of the updated model.[12] None of the 14 F7U-1s built between 1950 and 1952 were approved for use in squadron service.[3] On 7 July 1950, Vought test pilot Paul Thayer ejected from his burning prototype in front of an airshow crowd.[3] Around this time, Vought repeatedly noted its dissatisfaction with the Westinghouse J34 engine to the Navy, alleging that the powerplant was responsible for delivery delays and an inability to perform certain flight tests.[13]
Funding for the Cutlass was briefly cut before being reinstated during 1950.[14] The extent of the aircraft's development difficulties were such that, according to aviation author Tommy Thomason, there were serious considerations towards cancelling the Cutlass entirely during the latter half of 1951, however, severe difficulties with the Westinghouse J40 that powered many of its potential competing aircraft and thus the Navy had no solid alternative to readily take its place.[15] The introduction of more powerful steam catapults during 1952 also aided the programme considerably.[16]
On 20 December 1951, the improved F7U-3 took off for its maiden flight; this model was a reconfiguration of the aircraft towards a more general purpose fighter configuration.[16] Specific changes included the use of more powerful Westinghouse J46 engines, a stronger airframe that was enlarged by one-third, as well as better maintenance access via additional panels.[3][17] Test pilot (and later, astronaut) Wally Schirra wrote in his autobiography that he considered the F7U-3 to be accident prone and a "widow maker".[1] Several positive observations were also recorded by test pilots, such as it being a stable weapons platform, relatively maneuverable, fun to fly, and fairly sturdy with the strengthened airframe. Furthermore, test pilots gave particular praise for its high roll rate of 570 degrees/s, which was three times faster than most production jets at the time.[3] Some pilots have suggested that inexperience with swept wing aircraft, as well as other innovative features of the aircraft, likely contributed to the poor accident record.[1]
Early on, it was discovered that the Cutlass would gyrate after experiencing a stall. During one test flight, Lt. Morrey Loso's Cutlass exhibited such behavior, tumbling towards the ground following a stall. Upon letting go of the control stick to reach with both hands for the ejection handle, Loso's Cutlass promptly self-corrected. It was determined that normal recovery procedures did not apply to the Cutlass, a conclusion that was later confirmed via wind tunnel testing.[3]
The Vought F7U Cutlass was a carrier-based jet fighter and fighter-bomber. It featured broad chord, low aspect ratio swept wings, with twin wing-mounted tail fins either side of a short fuselage. There were no flaps.[4] The cockpit, which was pressurized, was situated well forward to provide good visibility for the pilot during aircraft carrier approaches.[1] The pilot was provisioned with an ejector seat.[4] Common nicknames for the F7U amongst naval aviators included the "Gutless Cutlass", the "Ensign Eliminator" and, in kinder moments, the "Praying Mantis".[18][3]
Both pitch and roll control was provided by elevons, though Vought referred to these surfaces as "ailevators" at the time. Slats were fitted to the entire span of the leading edge.[4] The aircraft was provisioned with all-hydraulic flight controls; these provided artificial feedback so the pilot could feel aerodynamic forces acting on the aircraft. The hydraulic system operated at 3000 psi, twice that of other Navy aircraft; however, the system proved to be not ready for front-line service and experienced a high level of unreliability.[3] Allegedly, this was at least partially due to many components having been intended for lower pressure hydraulic systems, resulting in a high rate of failure and thus exacerbating overall unreliability.[1]
During flight testing, aviator John Glenn and various test pilots found the muzzle blast from the 20mm cannons caused the engines to flame out, however this was solved when the US Navy approached weapons expert George M. Chinn who designed a flame-out eliminator,[19][20] a similar device to the Cutts compensator used on the Thompson submachine gun to divert the muzzle blast that solved the problem.
The very long nose landing gear strut required for high angle of attack takeoffs lifted the pilot 14 feet into the air and was fully steerable.[3][21] The high position of the nose relative to the flight deck posed visibility difficulties for the pilot.[22] Furthermore, the high stresses of barrier engagements, and side-loads imposed during early deployment carrier landings caused failure of the retract cylinder's internal down-locks, causing nose gear failure and resultant spinal injuries to the pilot.[18] To help mitigate the loading forces exerted upon the nose landing gear actuator and mounting structure, Vought's design engineers added small turbines, powered by bleed air from the engines, to pre-spin on the nosegear tires to 90 mph prior to landing.[3] Furthermore, an automatic fuel transfer system maintained the aircraft's center of gravity.[4]
The initial models of the Cutlass were powered by a pair of Westinghouse J34 turbojet engines; these were widely considered to be underpowered and several pilots disparagingly claimed that they "put out less heat than Westinghouse's toasters." The J34 produced considerably less power than had been originally projected by Westinghouse, yet it was the only engine that could fit the airframe of the Cutlass without extensive reworking.[3] Later production aircraft were provisioned with the more powerful Westinghouse J46 engine. The F7U-3M model was the first aircraft in US Navy service to be capable of firing the AAM-N-2 Sparrow I air-to-air missile.[3][23] While it had been intended to equip the Cutlass with radar, such apparatus would be excluded due to weight constraints.[24]
.jpg)
Production orders were placed for the F7U-1 under a specification that remained relatively close to that of the prototypes, and further developed F7U-2 and F7U-3 versions with more powerful engines. Because of development problems with the powerplant, however, the F7U-2 would never be built, while the F7U-3 would incorporate many refinements that came out of flight tests of the -1. The first 16 F7U-3s were powered by non-afterburning Allison J35-A-29 engines.[13] The -3, with its Westinghouse J46-WE-8B turbojets, would eventually become the definitive production version, a total of 288 aircraft equipping 13 U.S. Navy squadrons. Further development of the type came to an end shortly after flight testing of the more capable Vought F8U Crusader commenced.[citation needed]
The F7U's performance suffered due to a lack of sufficient engine thrust; consequently, its carrier landing and take-off performance was notoriously poor. The J35 was known to flame out in rain, a very serious fault. The first fleet squadron to receive F7Us was Fighter Squadron 81 (VF-81) in April 1954. Few squadrons made deployments with the type, and most "beached" them ashore during part of the cruise owing to operating difficulties. Those units known to have taken the type to sea were:
During 1957, Chance Vought analyzed the accident record and found that, with 78 accidents and a quarter of the airframes lost while accumulating 55,000 flight hours, the Cutlass had the highest accident rate of all Navy swept-wing fighters.[3] Furthermore, according to Thomason, accidents involving the Cutlass were typically more severe than with other aircraft.[25] The aircraft's poor safety record caused Vice Admiral Harold M. "Beauty" Martin, air commander of the United States Pacific Fleet, to replace the Cutlass with the Grumman F9F-8 Cougars; the decision was somewhat abrupt, with new aircraft continuing to be delivered for a time after this. Nevertheless, the outstanding order for 250 Cutlass A2U-1, a ground-attack variant, was soon cancelled.[3] During the late 1950s, the Navy donated many of the now-surplus aircraft to various municipalities and schools to promote aviation.[1]
The Navy Flight Demonstration Squadron, the Blue Angels, flew two F7U-1 Cutlasses (BuNos 124426 & 124427) as a side demonstration during their 1953 show season in an effort to promote the new aircraft, but did not use them as part of their regular formation demonstration. Both the pilots and ground crews found the aircraft generally unsatisfactory, and it was apparent that the type was still experiencing multiple teething troubles.[11] However, there were political pressures to adopt the Cutlass, both from several senior officers and from senators.[3] Among the failures were landing gear failures, hydraulic failures, engine fires while in the air and, on one occasion, a landing gear door fell on a spectator grandstand but, through sheer luck, did not injure anyone.[3][26]
During the Blue Angels' first airshow appearance in 1953, pilot Lt Edward "Whitey" Feightner, the former program manager for the F7U, experienced a total loss of hydraulics on a full afterburner takeoff and steep climb. While trying to gain enough altitude for ejection he was able to stay with the aircraft until the backup system came on. He clipped trees on the end of the runway, causing the left engine to flame out. With hydraulic fluid streaming back in a bright flame, he made a hard turn and got the plane back on the runway, much to the excitement of the crowd. Later, while traveling to an airshow at Naval Air Station Glenview in Chicago, Illinois, another Blue Angel pilot, Lt Harding MacKnight, experienced an engine flameout in his Cutlass, forcing him to make an emergency landing at NAS Glenview. Traveling with him, Feightner was redirected to make his landing at Chicago's former Orchard Airpark, which had been expanded and renamed O'Hare Airport. The runway had just been completed and was covered with peach baskets to prevent aircraft from landing until it was opened. Feightner was told to ignore the baskets and land on the new runway. As a result, Feightner's F7U became the first aircraft to land on the new runway for Chicago's O'Hare International Airport.
Following these incidents, the two Cutlasses were deemed unsuitable for demonstration flying and were flown to Naval Air Station Memphis, Tennessee, where they were abandoned to become aircraft maintenance instructional airframes for the Naval Technical Training Center.[27] The Blue Angels would opt to use the Grumman F9F Panther in place of the Cutlass.[3]
Seven F7U-3 Cutlass aircraft are known to have survived:
Data from Naval Fighters Number Six,[41] Jane's Encyclopedia of Aviation[42]
General characteristics
Performance
Armament
Aircraft of comparable role, configuration, and era
Related lists
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.
