Loading AI tools
Type of simple planetary gear train From Wikipedia, the free encyclopedia
A differential is a gear train with three drive shafts that has the property that the rotational speed of one shaft is the average of the speeds of the others. A common use of differentials is in motor vehicles, to allow the wheels at each end of a drive axle to rotate at different speeds while cornering. Other uses include clocks and analogue computers. Differentials can also provide a gear ratio between the input and output shafts (called the "axle ratio" or "diff ratio"). For example, many differentials in motor vehicles provide a gearing reduction by having fewer teeth on the pinion than the ring gear.
 | This article needs additional citations for verification. (July 2015) |
Milestones in the design or use of differentials include:
During cornering, the outer wheels of a vehicle must travel further than the inner wheels (since they are on a larger radius). This is easily accommodated when the wheels are not connected, however it becomes more difficult for the drive wheels, since both wheels are connected to the engine (usually via a transmission). Some vehicles (for example go-karts and trams) use axles without a differential, thus relying on wheel slip when cornering. However, for improved cornering abilities, many vehicles use a differential, which allows the two wheels to rotate at different speeds.
The purpose of a differential is to transfer the engine's power to the wheels while still allowing the wheels to rotate at different speeds when required. An illustration of the operating principle for a ring-and-pinion differential is shown below.
.jpg)
A relatively simple design of differential is used in rear-wheel drive vehicles, whereby a ring gear is driven by a pinion gear connected to the transmission. The functions of this design are to change the axis of rotation by 90 degrees (from the propshaft to the half-shafts) and provide a reduction in the gear ratio.
The components of the ring-and-pinion differential shown in the schematic diagram on the right are: 1. Output shafts (axles) 2. Drive gear 3. Output gears 4. Planetary gears 5. Carrier 6. Input gear 7. Input shaft (driveshaft)
An epicyclic differential uses epicyclic gearing to send certain proportions of torque to the front axle and the rear axle in an all-wheel drive vehicle.[citation needed] An advantage of the epicyclic design is that it is relatively compact width (when viewed along the axis of its input shaft).[citation needed]
.jpg)
A spur-gear differential has an equal-sized spur gears at each end, each of which is connected to an output shaft.[8] The input torque (i.e. from the engine or transmission) is applied to the differential via the rotating carrier.[8] Pinion pairs are located within the carrier and rotate freely on pins supported by the carrier. The pinion pairs only mesh for the part of their length between the two spur gears, and rotate in opposite directions. The remaining length of a given pinion meshes with the nearer spur gear on its axle. Each pinion connects the associated spur gear to the other spur gear (via the other pinion). As the carrier is rotated (by the input torque), the relationship between the speeds of the input (i.e. the carrier) and that of the output shafts is the same as other types of open differentials.
Uses of spur-gear differentials include the Oldsmobile Toronado American front-wheel drive car.[8][further explanation needed]
Locking differentials have the ability to overcome the chief limitation of a standard open differential by essentially "locking" both wheels on an axle together as if on a common shaft. This forces both wheels to turn in unison, regardless of the traction (or lack thereof) available to either wheel individually. When this function is not required, the differential can be "unlocked" to function as a regular open differential.
Locking differentials are mostly used on off-road vehicles, to overcome low-grip and variable grip surfaces.
An undesirable side-effect of a regular ("open") differential is that it can send most of the power to the wheel with the lesser traction (grip).[9][10] In situation when one wheel has reduced grip (e.g. due to cornering forces or a low-grip surface under one wheel), an open differential can cause wheelspin in the tyre with less grip, while the tyre with more grip receives very little power to propel the vehicle forward.[11]
In order to avoid this situation, various designs of limited-slip differentials are used to limit the difference in power sent to each of the wheels.
Torque vectoring is a technology employed in automobile differentials that has the ability to vary the torque to each half-shaft with an electronic system; or in rail vehicles which achieve the same using individually motored wheels. In the case of automobiles, it is used to augment the stability or cornering ability of the vehicle.
| This section needs additional citations for verification. (March 2023) |
Non-automotive uses of differentials include performing analogue arithmetic. Two of the differential's three shafts are made to rotate through angles that represent (are proportional to) two numbers, and the angle of the third shaft's rotation represents the sum or difference of the two input numbers. The earliest known use of a differential gear is in the Antikythera mechanism, c. 80 BCE, which used a differential gear to control a small sphere representing the Moon from the difference between the Sun and Moon position pointers. The ball was painted black and white in hemispheres, and graphically showed the phase of the Moon at a particular point in time.[1] An equation clock that used a differential for addition was made in 1720. In the 20th century, large assemblies of many differentials were used as analogue computers, calculating, for example, the direction in which a gun should be aimed.[12]
Chinese south-pointing chariots may also have been very early applications of differentials. The chariot had a pointer which constantly pointed to the south, no matter how the chariot turned as it travelled. It could therefore be used as a type of compass. It is widely thought that a differential mechanism responded to any difference between the speeds of rotation of the two wheels of the chariot, and turned the pointer appropriately. However, the mechanism was not precise enough, and, after a few miles of travel, the dial could be pointing in the wrong direction.
The earliest verified use of a differential was in a clock made by Joseph Williamson in 1720. It employed a differential to add the equation of time to local mean time, as determined by the clock mechanism, to produce solar time, which would have been the same as the reading of a sundial. During the 18th century, sundials were considered to show the "correct" time, so an ordinary clock would frequently have to be readjusted, even if it worked perfectly, because of seasonal variations in the equation of time. Williamson's and other equation clocks showed sundial time without needing readjustment. Nowadays, we consider clocks to be "correct" and sundials usually incorrect, so many sundials carry instructions about how to use their readings to obtain clock time.
Differential analysers, a type of mechanical analogue computer, were used from approximately 1900 to 1950. These devices used differential gear trains to perform addition and subtraction.
The Mars rovers Spirit and Opportunity (both launched in 2004) used differential gears in their rocker-bogie suspensions to keep the rover body balanced as the wheels on the left and right move up and down over uneven terrain.[13] The Curiosity and Perseverance rovers used a differential bar instead of gears to perform the same function.[14]
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.
