Loading AI tools
Device worn to protect the user from inhaling contaminants From Wikipedia, the free encyclopedia
A respirator is a device designed to protect the wearer from inhaling hazardous atmospheres including lead fumes, vapours, gases and particulate matter such as dusts and airborne pathogens such as viruses. There are two main categories of respirators: the air-purifying respirator, in which respirable air is obtained by filtering a contaminated atmosphere, and the air-supplied respirator, in which an alternate supply of breathable air is delivered. Within each category, different techniques are employed to reduce or eliminate noxious airborne contaminants.
Air-purifying respirators range from relatively inexpensive, single-use, disposable face masks, known as filtering facepiece respirators, reusable models with replaceable cartridges called elastomeric respirators, to Powered air-purifying respirators (PAPR), which use a pump or fan to constantly move air through a filter and supply purified air into a mask, helmet or hood.
The history of protective respiratory equipment can be traced back as far as the first century, when Pliny the Elder (c. 23 AD–79) described using animal bladder skins to protect workers in Roman mines from red lead oxide dust.[1] In the 16th century, Leonardo da Vinci suggested that a finely woven cloth dipped in water could protect sailors from a toxic weapon made of powder that he had designed.[2]
Alexander von Humboldt introduced a primitive respirator in 1799 when he worked as a mining engineer in Prussia.[3]
Julius Jeffreys first used the word "respirator" as a mask in 1836.[4]
In 1848, the first US patent for an air-purifying respirator was granted to Lewis P. Haslett[5] for his 'Haslett's Lung Protector,' which filtered dust from the air using one-way clapper valves and a filter made of moistened wool or a similar porous substance.[6] Hutson Hurd patented a cup-shaped mask in 1879 which became widespread in industrial use.[7]
Inventors in Europe included John Stenhouse, a Scottish chemist, who investigated the power of charcoal in its various forms, to capture and hold large volumes of gas. He built one of the first respirators able to remove toxic gases from the air, paving the way for activated charcoal to become the most widely used filter for respirators.[8] Irish physicist John Tyndall took Stenhouse's mask, added a filter of cotton wool saturated with lime, glycerin, and charcoal, and in 1871 invented a 'fireman's respirator', a hood that filtered smoke and gas from air, which he exhibited at a meeting of the Royal Society in London in 1874.[9] Also in 1874, Samuel Barton patented a device that 'permitted respiration in places where the atmosphere is charged with noxious gases, or vapors, smoke, or other impurities.'[10][11]
In the late 19th century, Miles Philips began using a "mundebinde" ("mouth bandage") of sterilized cloth which he refined by adapting a chloroform mask with two layers of cotton mull.[12]
In the winter of 1910, Wu was given instructions from the Foreign Office of the Imperial Qing court[13] in Peking, to travel to Harbin to investigate an unknown disease that killed 99.9% of its victims.[14] This was the beginning of the large pneumonic plague epidemic of Manchuria and Mongolia, which ultimately claimed 60,000 lives.[15]
Wu was able to conduct a postmortem (usually not accepted in China at the time) on a Japanese woman who had died of the plague.[16][17] Having ascertained via the autopsy that the plague was spreading by air, Wu developed surgical masks into more substantial masks with layers of gauze and cotton to filter the air.[18][19] Gérald Mesny, a prominent French doctor who had come to replace Wu, refused to wear a mask and died days later of the plague.[17][18][16] The mask was widely produced, with Wu overseeing the production and distribution of 60,000 masks in a later epidemic, and it featured in many press images.[20][18]The First World War brought about the first need for mass-produced gas masks on both sides because of extensive use of chemical weapons. The German army successfully used poison gas for the first time against Allied troops at the Second Battle of Ypres, Belgium on April 22, 1915.[21] An immediate response was cotton wool wrapped in muslin, issued to the troops by May 1. This was followed by the Black Veil Respirator, invented by John Scott Haldane, which was a cotton pad soaked in an absorbent solution which was secured over the mouth using black cotton veiling.[22]
Seeking to improve on the Black Veil respirator, Cluny MacPherson created a mask made of chemical-absorbing fabric which fitted over the entire head.[23] A 50.5 cm × 48 cm (19.9 in × 18.9 in) canvas hood treated with chlorine-absorbing chemicals, and fitted with a transparent mica eyepiece.[24] Macpherson presented his idea to the British War Office Anti-Gas Department on May 10, 1915; prototypes were developed soon after.[25] The design was adopted by the British Army and introduced as the British Smoke Hood in June 1915; Macpherson was appointed to the War Office Committee for Protection against Poisonous Gases.[26] More elaborate sorbent compounds were added later to further iterations of his helmet (PH helmet), to defeat other respiratory poison gases used such as phosgene, diphosgene and chloropicrin. In summer and autumn 1915, Edward Harrison, Bertram Lambert and John Sadd developed the Large Box Respirator.[27] This canister gas mask had a tin can containing the absorbent materials by a hose and began to be issued in February 1916. A compact version, the Small Box Respirator, was made a universal issue from August 1916.[citation needed]Prior to the 1970s, respirator standards were under the purview of the US Bureau of Mines (USBM). An example of an early respirator standard, Type A, established in 1926, was intended to protect against mechanically generated dusts produced in mines. These standards were intended to obviate miner deaths, noted to have reached 3,243 by 1907. However, prior to the Hawks Nest Tunnel Disaster, these standards were merely advisory, as the USBM had no enforcement power at the time.[28] After the disaster, an explicit approval program was established in 1934, along with the introduction of combination Type A/B/C respirator ratings, corresponding to Dusts/Fumes/Mists respectively, with Type D blocking all three.[29]
The Federal Coal Mine Health and Safety Act establishing MESA (later MSHA),[30] the Occupational Safety and Health Act of 1970, establishing NIOSH,[31] as well as other regulations established around the time, reshuffled regulatory authority for respirators, but nonetheless continued the use of USBM-era regulations.[29]In the 1970s, the successor to the United States Bureau of Mines and NIOSH developed standards for single-use respirators, and the first single-use respirator was developed by 3M and approved in 1972.[32] 3M used a melt blowing process that it had developed decades prior and used in products such as ready-made ribbon bows and bra cups; its use in a wide array of products had been pioneered by designer Sara Little Turnbull.[33]
Historically, respirators in the US had generally been approved by MESA/MSHA/NIOSH under federal regulation 30 CFR 11. On July 10, 1995, in response to respirators exhibiting "low initial efficiency levels", new 42 CFR 84 standards, including the N95 standard, were enforced under a three-year transition period,[34] ending on July 1, 1998. The standard for N95 respirators includes, but is not limited to, a filtration of at least 95% under a 0.3 micrometer 200 milligram test load of sodium chloride. Standards and specifications are also subject to change.[35]
Once 42 CFR 84 was in effect, MSHA, under a proposed rule change to 30 CFR 11, 70, and 71, would withdraw from the approval process of rated respirators (outside of respirators used for mining).[36][37]
China normally makes 10 million masks per day, about half of the world production. During the COVID-19 pandemic, 2,500 factories were converted to produce 116 million daily.[38]
During the COVID-19 pandemic, people in the United States, and in a lot of countries in the world, were urged to make their own cloth masks due to the widespread shortage of commercial masks.[39]
All respirators have some type of facepiece held to the wearer's head with straps, a cloth harness, or some other method. Facepieces come in many different styles and sizes to accommodate all types of face shapes.
A full facepiece covers the mouth, nose and eyes and if sealed, is sealed round the perimeter of the face. Unsealed versions may be used when air is supplied at a rate which prevents ambient gas from reaching the nose or mouth during inhalation.
Respirators can have half-face forms that cover the bottom half of the face including the nose and mouth, and full-face forms that cover the entire face. Half-face respirators are only effective in environments where the contaminants are not toxic to the eyes or facial area.
An escape respirator may have no component that would normally be described as a mask, and may use a bite-grip mouthpiece and nose clip instead. Alternatively, an escape respirator could be a time-limited self-contained breathing apparatus.
For hazardous environments, like confined spaces, atmosphere-supplying respirators, like SCBAs, should be used.
A wide range of industries use respirators including healthcare & pharmaceuticals, defense & public safety services (defense, firefighting & law enforcement), oil and gas industries, manufacturing (automotive, chemical, metal fabrication, food and beverage, wood working, paper and pulp), mining, construction, agriculture and forestry, cement production, power generation, painting, shipbuilding, and the textile industry.[43]
Respirators require user training in order to provide proper protection.
Each time a wearer dons a respirator, they must perform a seal check to be sure that they have an airtight seal to the face so that air does not leak around the edges of the respirator. (PAPR respirators may not require this because they don't necessarily seal to the face.) This check is different than the periodic fit test that is performed by specially trained personnel using testing equipment. Filtering facepiece respirators are typically checked by cupping the hands over the facepiece while exhaling (positive pressure check) or inhaling (negative pressure check) and observing any air leakage around the facepiece. Elastomeric respirators are checked in a similar manner, except the wearer blocks the airways through the inlet valves (negative pressure check) or exhalation valves (positive pressure check) while observing the flexing of the respirator or air leakage. Manufacturers have different methods for performing seal checks and wearers should consult the specific instructions for the model of respirator they are wearing. Some models of respirators or filter cartridges have special buttons or other mechanisms built into them to facilitate seal checks.[44]
A respirator fit test checks whether a respirator properly fits the face of someone who wears it. The fitting characteristic of a respirator is the ability of the mask to separate a worker's respiratory system from ambient air.
This is achieved by tightly pressing the mask flush against the face (without gaps) to ensure an efficient seal on the mask perimeter. Because wearers cannot be protected if there are gaps, it is necessary to test the fit before entering into contaminated air. Multiple forms of the test exist.A surgical mask is a loosely-placed, unsealed barrier, meant to stop droplets, and other liquid-borne particles from the mouth and nose that may contain pathogens.[45]
A surgical mask may not block all particles, due to the lack of fit between the surface of the face mask and the face.[45] The filtration efficiency of a surgical mask ranges between 10% to 90% for any given manufacturer, when measured using tests required for NIOSH certification. A study found that 80–100% of subjects failed an OSHA-accepted qualitative fit test, and a quantitative test showed between 12–25% leakage.[46]
A CDC study found that in public indoor settings, consistently wearing a respirator was linked to a 83% lower risk of testing positive for COVID-19, as compared to a 66% reduction when using surgical masks, and 56% for cloth.[47]Respirators used in healthcare are traditionally a specific variant called a surgical respirator, which is both approved by NIOSH as a respirator and cleared by the Food and Drug Administration as a medical device similar to a surgical mask.[48] These may also be labeled "Surgical N95", "medical respirators", or "healthcare respirators".[49] The difference lies in the extra fluid-resistant layer outside, typically colored blue.[50] In addition to 42 CFR 84, surgical N95s are regulated under FDA regulation 21 CFR 878.4040.[51]
In the United States, the Occupational Safety and Health Administration (OSHA) requires healthcare workers who are expected to perform patient activities with those suspected or confirmed to be infected with COVID-19 to wear respiratory protection, such as an N95 respirator.[52] The CDC recommends the use of respirators with at least N95 certification to protect the wearer from inhalation of infectious particles including Mycobacterium tuberculosis, avian influenza, severe acute respiratory syndrome (SARS), pandemic influenza, and Ebola.[53]Air-purifying respirators are respirators that draw in the surrounding air and purify it before it is breathed (unlike air-supplying respirators, which are sealed systems, with no air intake, like those used underwater). Air-purifying respirators filter particulates, gases, and vapors from the air, and may be negative-pressure respirators driven by the wearer's inhalation and exhalation, or positive-pressure units such as powered air-purifying respirators (PAPRs).
According to the NIOSH Respirator Selection Logic, air-purifying respirators are recommended for concentrations of hazardous particulates or gases that are greater than the relevant occupational exposure limit but less than the immediately dangerous to life or health level and the manufacturer's maximum use concentration, subject to the respirator having a sufficient assigned protection factor. For substances hazardous to the eyes, a respirator equipped with a full facepiece, helmet, or hood is recommended. Air-purifying respirators are not effective during firefighting, in oxygen-deficient atmosphere, or in an unknown atmosphere; in these situations a self-contained breathing apparatus is recommended instead.[54]
Mechanical filters remove contaminants from air in several ways: interception when particles following a line of flow in the airstream come within one radius of a fiber and adhere to it; impaction, when larger particles unable to follow the curving contours of the airstream are forced to embed in one of the fibers directly; this increases with diminishing fiber separation and higher air flow velocity; by diffusion, where gas molecules collide with the smallest particles, especially those below 100 nm in diameter, which are thereby impeded and delayed in their path through the filter, increasing the probability that particles will be stopped by either of the previous two mechanisms; and by using an electrostatic charge that attracts and holds particles on the filter surface.
There are many different filtration standards that vary by jurisdiction. In the United States, the National Institute for Occupational Safety and Health defines the categories of particulate filters according to their NIOSH air filtration rating. The most common of these are the N95 respirator, which filters at least 95% of airborne particles but is not resistant to oil.
Other categories filter 99% or 99.97% of particles, or have varying degrees of resistance to oil.[55]
In the European Union, European standard EN 143 defines the 'P' classes of particle filters that can be attached to a face mask, while European standard EN 149 defines classes of "filtering half masks" or "filtering facepieces", usually called FFP masks.[56]
According to 3M, the filtering media in respirators made according to the following standards are similar to U.S. N95 or European FFP2 respirators, however, the construction of the respirators themselves, such as providing a proper seal to the face, varies considerably. (For example, US NIOSH-approved respirators never include earloops because they don't provide enough support to establish a reliable, airtight seal.) Standards for respirator filtration the Chinese KN95, Australian / New Zealand P2, Korean 1st Class also referred to as KF94, and Japanese DS.[57]
Chemical cartridge respirators use a cartridge to remove gases, volatile organic compounds (VOCs), and other vapors from breathing air by adsorption, absorption, or chemisorption. A typical organic vapor respirator cartridge is a metal or plastic case containing from 25 to 40 grams of sorption media such as activated charcoal or certain resins. The service life of the cartridge varies based, among other variables, on the carbon weight and molecular weight of the vapor and the cartridge media, the concentration of vapor in the atmosphere, the relative humidity of the atmosphere, and the breathing rate of the respirator wearer. When filter cartridges become saturated or particulate accumulation within them begins to restrict air flow, they must be changed.[58]
If the concentration of harmful gases is immediately dangerous to life or health, in workplaces covered by the Occupational Safety and Health Act the US Occupational Safety and Health Administration specifies the use of air-supplied respirators except when intended solely for escape during emergencies.[59] NIOSH also discourages their use under such conditions.[60]
Elastomeric respirators, also called reusable air-purifying respirators,[63] seal to the face with elastomeric material, which may be a natural or synthetic rubber. They are generally reusable. Full-face versions of elastomeric respirators seal better and protect the eyes.[64]
Elastomeric respirators consist of a reusable mask that seals to the face, with exchangeable filters.[65][66] Elastomeric respirators can be used with chemical cartridge filters that remove gases, mechanical filters that retain particulate matter, or both.[67] As particulate filters, they are comparable[65] (or, due to the quality and error-tolerance of the elastomeric seal, possibly superior[67]) to filtering facepiece respirators such as most disposable N95 respirators and FFP masks.[65]These respirators do not purify the ambient air, but supply breathing gas from another source. The three types are the self contained breathing apparatus, in which a compressed air cylinder is worn by the wearer; the supplied air respirators, where a hose supplies air from a stationary source; and combination supplied-air respirators, with a emergency backup tank.[68]
A self-contained breathing apparatus (SCBA) is a respirator worn to provide an autonomous supply of breathable gas in an atmosphere that is immediately dangerous to life or health from a gas cylinder.[69] They are typically used in firefighting and industry. The term self-contained means that the SCBA is not dependent on a remote supply of breathing gas (e.g., through a long hose). They are sometimes called industrial breathing sets. Some types are also referred to as a compressed air breathing apparatus (CABA) or simply breathing apparatus (BA). Unofficial names include air pack, air tank, oxygen cylinder or simply pack, terms used mostly in firefighting. If designed for use under water, it is also known as a scuba set (self-contained underwater breathing apparatus).
An open circuit SCBA typically has three main components: a high-pressure gas storage cylinder, (e.g., 2,216 to 5,500 psi (15,280 to 37,920 kPa), about 150 to 374 atmospheres), a pressure regulator, and a respiratory interface, which may be a mouthpiece, half mask or full-face mask, assembled and mounted on a framed carrying harness.[70]
A self-contained breathing apparatus may fall into one of three categories: open-circuit, closed-circuit,[71] or continuous-flow.[72]A self-contained self-rescue device, SCSR, self-contained self-rescuer, or air pack is a type of closed-circuit SCBA[84] with a portable oxygen source for providing breathable air when the surrounding atmosphere lacks oxygen or is contaminated with toxic gases, e.g. carbon monoxide.
Self-rescuers are intended for use in environments such as coal mines where there is a risk of fire or explosion, and in a location where no external rescue may be available for some time – the wearer must make their own way to safety, or to some pre-equipped underground refuge. The main hazard here is from large quantities of carbon monoxide or whitedamp, often produced by an explosion of firedamp. In some industries, the hazard may be from anoxic asphyxia, or a lack of oxygen, rather than poisoning by something toxic.
Self-rescuers are small, lightweight belt or harness-worn devices, enclosed in a rugged metal case. They are designed to have a long service life of around 10 years (longer for shelf storage) and to be worn every day by each miner. Once used, they have a working life of a few hours and are discarded after opening.The Hierarchy of Controls, noted as part of the Prevention Through Design initiative started by NIOSH with other standards bodies, is a set of guidelines emphasizing building in safety during design, as opposed to ad-hoc solutions like PPE, with multiple entities providing guidelines on how to implement safety during development[85] outside of NIOSH-approved respirators. US Government entities currently and formerly involved in the regulation of respirators follow the Hierarchy of Controls, including OSHA[86] and MSHA.[87]
However, some HOC implementations, notably MSHA's, have been criticized for allowing mining operators to skirt engineering control noncompliance by requiring miners to wear respirators instead if the permissible exposure limit (PEL) is exceeded, without work stoppages, breaking the hierarchy of engineering controls. Another concern was fraud related to the inability to scrutinize engineering controls,[88][89] unlike NIOSH-approved respirators, like the N95, which can be fit tested by anyone, are subject to the scrutiny of NIOSH, and are trademarked and protected under US federal law.[90]
With regards to people complying with requirements to wear respirators, various papers note high respirator non-compliance across industries,[91][92] with a survey noting non-compliance was due in large part due to discomfort from temperature increases along the face, and a large amount of respondents also noting the social unacceptability of provided N95 respirators during the survey.[93] For reasons like mishandling, ill-fitting respirators and lack of training, the Hierarchy of Controls dictates respirators be evaluated last while other controls exist and are working. Alternative controls like hazard elimination, administrative controls, and engineering controls like ventilation are less likely to fail due to user discomfort or error.[94][95]
A U.S. Department of Labor study[96] showed that in almost 40 thousand American enterprises, the requirements for the correct use of respirators are not always met. Experts note that in practice it is difficult to achieve elimination of occupational morbidity with the help of respirators:
It is well known how ineffective ... trying to compensate the harmful workplace conditions with ... the use of respirators by employees.[97] Unfortunately, the only certain way of reducing the exceedance fraction to zero is to ensure that Co (note: Co - concentration of pollutants in the breathing zone) never exceeds the PEL value.[98]
Certain types of facial hair can reduce fit to a significant degree. For this reason, there are facial hair guidelines for respirator users.[99] This is another example of potential respirator non-compliance.
Another disadvantage of respirators is that the onus is on the respirator user to determine if their respirator is counterfeit or has had its certification revoked.[90] Customers and employers can inadvertently purchase non-OEM parts for a NIOSH-approved respirator which void the NIOSH approval and violate OSHA laws, in addition to potentially compromising the fit of the respirator.[100] This is another example of respirator mishandling under the Hierarchy of Controls.
If respirators must be used, under 29 CFR 1910.134, OSHA requires respirator users to conduct a respirator fit test, with a safety factor of 10 to offset lower fit during real world use.[86] However, NIOSH notes the large amount of time required for fit testing has been a point of contention for employers.[101]
Other opinions concern the change in performance of respirators in use compared to when fit testing, and compared to engineering control alternatives:
The very limited field tests of air-purifying respirator performance in the workplace show that respirators may perform far less well under actual use conditions than is indicated by laboratory fit factors. We are not yet able to predict the level of protection accurately; it will vary from person to person, and it may also vary from one use to the next for the same individual. In contrast, we can predict the effectiveness of engineering controls, and we can monitor their performance with commercially available state-of-the-art devices.[102]
Extended use of certain negative-pressure respirators can result in higher levels of carbon dioxide from dead space and breathing resistance (pressure drop) which can impact functioning and sometimes can exceed the PEL.[103][104][105] This effect was significantly reduced with powered air purifying respirators.[106] Certain respirator designs, especially those with head straps, can also lead to headaches,[107] dermatitis and acne.[108]
Complaints have been leveled at early LANL NIOSH fit test panels (which included primarily military personnel) as being unrepresentative of the broader American populace.[109] However, later fit test panels, based on a NIOSH facial survey conducted in 2003, were able to reach 95% representation of working US population surveyed.[110] Despite these developments, 42 CFR 84, the US regulation NIOSH follows for respirator approval, allows for respirators that don't follow the NIOSH fit test panel provided that: more than one facepiece size is provided, and no chemical cartridges are made available.[111]
Respirators designed to non-US standards may not be subject to as much or any scrutiny:
Some jurisdictions allow for respirator filtration ratings lower than 95%, respirators which are not rated to prevent respiratory infection, asbestos, or other dangerous occupational hazards. These respirators are sometimes known as dust masks for their almost exclusive approval only against dust nuisances:
In the US, NIOSH noted that under standards predating the N95, 'Dust/Mist' rated respirators could not prevent the spread of TB.[114]
The choice and use of respirators in developed countries is regulated by national legislation. To ensure that employers choose respirators correctly, and perform high-quality respiratory protection programs, various guides and textbooks have been developed:
Textbooks and guidelines for the selection and use of respirators | ||||
---|---|---|---|---|
Country | Language | Year of publication | Pages | Institution (hyperlink to document) |
US | English | 1987 | 305 | NIOSH ([115]) |
US | English | 2005 | 32 | NIOSH ([116]) |
US | English | 1999 | 120 | NIOSH ([117]) |
US | English | 2017 | 48 | Pesticide Educational Resources Collaborative (PERC) ([118]) |
US | English & Spanish | - | - | OSHA ([119]) |
US | English | 2011 | 124 | OSHA ([120]) |
US | English | 2015 | 96 | OSHA ([121]) |
US | English | 2012 | 44 | OSHA ([122]) |
US | English | 2014 | 44 | OSHA ([123]) |
US | English | 2016 | 32 | OSHA ([124]) |
US | English | 2014 | 38 | OSHA ([125]) |
US | English | 2017 | 51 | OSHA ([126]) |
US | English | 2001 | 166 | NRC ([127]) |
US | English | 1986 | 173 | NIOSH & EPA ([128]) |
Canada | French | 2013, 2002 | 60 | Institut de recherche Robert-Sauve en santé et en sécurité du travail (IRSST) ([129]) |
Canada | English | 2015 | - | Institut de recherche Robert-Sauve en sante et en securite du travai (IRSST) ([130]) |
Canada | French | 2015 | - | Institut de recherche Robert-Sauve en sante et en securite du travai (IRSST) ([131]) |
France | French | 2017 | 68 | Institut National de Recherche et de Sécurité (INRS) ([132]) |
Germany | German | 2011 | 174 | Spitzenverband der gewerblichen Berufsgenossenschaften und der Unfallversicherungsträger der öffentlichen Hand (DGUV) ([133]) |
UK | English | 2013 | 59 | The Health and Safety Executive (HSE) ([134]) |
UK | English | 2016 | 29 | The UK Nuclear Industry Good PracIndustry Radiological Protection Coordination Group (IRPCG) ([135]) |
Ireland | English | 2010 | 19 | The Health and Safety Authority (HSA) ([136]) |
New Zealand | English | 1999 | 51 | Occupational Safety and Health Service (OSHS) ([137]) |
Chile | Spanish | 2009 | 40 | Instituto de Salud Publica de Chile (ISPCH) ([138]) |
Spain | Spanish | - | 16 | Instituto Nacional de Seguridad, Salud y Bienestar en el Trabajo (INSHT) ([139]) |
For standard filter classes used in respirators, see Mechanical filter (respirator)#Filtration standards.
Seamless Wikipedia browsing. On steroids.
Every time you click a link to Wikipedia, Wiktionary or Wikiquote in your browser's search results, it will show the modern Wikiwand interface.
Wikiwand extension is a five stars, simple, with minimum permission required to keep your browsing private, safe and transparent.